Additional Safety Information - Bosch AdvancedTableCut 52 Originalbetriebsanleitung

Use extra caution when making a cut into blind areas
u
of assembled workpieces. The protruding saw blade
may cut objects that can cause kickback.
Support large panels to minimise the risk of saw blade
u
pinching and kickback. Large panels tend to sag under
their own weight. Support(s) must be placed under all
portions of the panel overhanging the table top.
Use extra caution when cutting a workpiece that is
u
twisted, knotted, warped or does not have a straight
edge to guide it with a mitre gauge or along the fence.
A warped, knotted, or twisted workpiece is unstable and
causes misalignment of the kerf with the saw blade, bind-
ing and kickback.
Never cut more than one workpiece, stacked vertic-
u
ally or horizontally. The saw blade could pick up one or
more pieces and cause kickback.
When restarting the saw with the saw blade in the
u
workpiece, centre the saw blade in the kerf so that the
saw teeth are not engaged in the material. If the saw
blade binds, it may lift up the workpiece and cause kick-
back when the saw is restarted.
Keep saw blades clean, sharp, and with sufficient set.
u
Never use warped saw blades or saw blades with
cracked or broken teeth. Sharp and properly set saw
blades minimise binding, stalling and kickback.
Table saw operating procedure warnings
Turn off the table saw and disconnect the power cord
u
when removing the table insert, changing the saw
blade or making adjustments to the riving knife or saw
blade guard, and when the machine is left unattended.
Precautionary measures will avoid accidents.
Never leave the table saw running unattended. Turn it
u
off and don't leave the tool until it comes to a com-
plete stop. An unattended running saw is an uncontrolled
hazard.
Locate the table saw in a well-lit and level area where
u
you can maintain good footing and balance. It should
be installed in an area that provides enough room to
easily handle the size of your workpiece. Cramped,
dark areas, and uneven slippery floors invite accidents.
Frequently clean and remove sawdust from under the
u
saw table and/or the dust collection device. Accumu-
lated sawdust is combustible and may self-ignite.
The table saw must be secured. A table saw that is not
u
properly secured may move or tip over.
Remove tools, wood scraps, etc. from the table before
u
the table saw is turned on. Distraction or a potential jam
can be dangerous.
Never stand on the table saw, do not use it as a step-
u
ping stool. Serious injury could occur if the tool is tipped
or if the cutting tool is accidentally contacted.

Additional safety information

When mounting the saw blade, wear protective
u
gloves. This poses a risk of injury.
Bosch Power Tools
Do not touch the saw blade after working before it has
u
cooled. The saw blade becomes very hot while working.
Keep your work area clean. Material mixtures are partic-
u
ularly hazardous. Light metal dust may catch fire or ex-
plode.
Store the power tool safely when it is not in use. The
u
storage location must be dry and lockable. This pre-
vents the power tool from storage damage, and from be-
ing operated by untrained persons.
Never use the power tool if the cable is damaged. Do
u
not touch the damaged cable and pull out the mains
plug if the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
Check the cable regularly and have a damaged cable
u
repaired only by an authorised customer service
agent for Bosch power tools. Replace damaged exten-
sion cables. This will ensure that the safety of the power
tool is maintained.
Do not use the power tool for cutting slots (stopped
u
grooves).
Never reach behind the saw blade to hold onto the
u
workpiece, remove wood chips or for any other
reason. The clearance between your hand and the rotat-
ing saw blade is too small when you do this.
Operating as a saw: Guide the saw blade against the
u
workpiece only when the saw is switched on. Other-
wise there is a risk of kickback occurring if the saw blade
catches in the workpiece.
Operation as a table saw: Only advance the workpiece
u
towards the saw blade when it is running. Otherwise
there is a risk of kickback occurring if the saw blade
catches in the workpiece.
Operate the power tool only when the work area up to
u
the workpiece is clear of any adjusting tools, wood
chips, etc. Small pieces of wood or other objects that
come in contact with the rotating saw blade can strike the
operator with high speed.
Only saw one workpiece at a time. Workpieces placed
u
on top of or alongside each other can cause the saw blade
to jam or the workpieces to move out of place and against
each other when sawing.
Always use the universal guide. This improves the cut-
u
ting accuracy and reduces the possibility of the saw blade
jamming.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
English | 21
1 609 92A 66E | (12.01.2021)