Bosch AdvancedTableCut 52 Originalbetriebsanleitung Seite 23

Technical Data
Table saw/pull-push saw
Article number
Rated power input W
-1
No-load speed min
Saw blade receptacle
Weight according to kg
EPTA-Procedure
01:2014
Protection class
Maximum workpiece dimensions (see "Maximum Workpiece Dimen-
sions", page 26)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise Information
Noise emission values determined according
to EN 62841-3-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 90 dB(A); sound power
level 100 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
Bosch Power Tools
– Table saw/pull-push saw
(Mounted: Saw blade (3))
AdvancedTableCut 52
– Universal guide (2)
3 603 M12 0..
– Additional stop (21)
550
– Push stick (9) with screw grabber (37)
8200
– Workpiece support (34)
SDS
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
8.5
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
/ II
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Initial Start-up
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
Mounting the Stops
Mounting the universal guide (see figure A)
– Insert the rail (23) for the universal guide (2) into the de-
sired guide groove (24) or (25) of the saw table.
– To lock the universal guide in the middle guide groove
(25) or in the guide groove (24), tighten the clamping
lever (1) clockwise.
To change the position of the clamping lever (1), pull the
clamping lever up and turn it until it reaches the desired
position.
– To lock the universal guide in the guide groove (24),
tighten the knurled screw (19), if the workpiece projects
over the saw table.
Mounting the additional stop (see figure B)
To make it easier to position long workpieces for rip cuts, the
additional stop (21) can be mounted on the universal guide
(2).
– To remove the additional stop (21) from the holder under
the saw table, press the release button (26) and pull out
the stop to the rear.
– Push the additional stop (21) together with the two wing
bolts (27) from above into the grooves of the universal
guide (2) until the additional stop is lying on the saw
table.
– Tighten the two wing bolts (27) by turning them clock-
wise.
Note: Ensure that the additional stop is positioned fully on
the saw table.
English | 23
1 609 92A 66E | (12.01.2021)