Noise Information; Items Included - Bosch GCM 8 SJL Professional HEAVY DUTY Originalbetriebsanleitung

28 | English
Sliding mitre saw
Laser type nm
mW
Laser class
Divergence of mrad
laser line (full
angle)
Weight according kg
to EPTA-Proced-
ure 01:2014
Protection class
Dimensions of suitable saw blades
Saw blade dia- mm
meter
Base blade thick- mm
ness
Max. cutting width mm
Hole diameter mm
Permissible workpiece dimensions (see "Permissible workpiece dimensions", page 32)
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise information

Noise emission values determined according to EN
62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 99 dB(A); sound power level
112 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
1 609 92A 4D3 | (30.08.2018)
GCM 8 SJL GCM 8 SJL
650 650
< 0.39 < 0.39
1M 1M
1.0 1.0
17.3 17.3
/ II / II
216 216
1.3−1.8 1.3−1.8
3.3 3.3
30 30

Items included

Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Sliding mitre saw with mounted saw blade
– Screw clamp (28)
– Hex key (33)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them repaired or replaced by an authorised ser-
vice centre immediately.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figures a1−a2)
– Use suitable screw fasteners to secure the power tool to
the work surface. Use the holes (26) to do this.
or
– Firmly clamp the base of the power tool to the work sur-
face with commercially available screw clamps.
Mounting on a Bosch saw stand
With the height-adjustable legs, Bosch GTA saw stands
provide firm support for the power tool on any surface. The
GCM 8 SJL GCM 8 SJL
650 650
< 0.39 < 0.39
1M 1M
1.0 1.0
17.3 17.3
/ II / II
216 216
1.3−1.8 1.3−1.8
3.3 3.3
25.4 25.4
GCM 8 SJL
650
< 0.39
1M
1.0
17.3
/ II
216
1.3−1.8
3.3
25.4
Bosch Power Tools