Technical Data - Hameg R&S HM8118 Benutzerhandbuch

Technical Data

Technical Data
11 Technical Data
200 kHz LCR-Bridge R&S®HM8118
All data valid at 23 °C after 30 minutes warm-up.
Conditions
Test signal voltage 1 V
Open and short corrections performed
Measurement time SLOW
Display
Measurement modes Auto, L-Q, L-R, C-D, C-R, R-Q, Z-Θ, Y-Θ, R-X,
G-B, N-Θ, M
Equivalent circuits auto, series or parallel
Parameters displayed Value, deviation or % deviation
Averaging 2 to 99 measurements
Accuracy
Primary parameters Basic accuracy
(Test voltage: 1.0 V,
measurement SLOW/MEDIUM,
autoranging mode, constant voltage OFF,
bias off). For FAST mode double the basic
accuracy values
Impedance: 100 MΩ
0.2% + I Z I / 1.5 GΩ
4 MΩ
1 MΩ
0.05% +
I Z I / 2 GΩ
25 kΩ
100 Ω
0.1% + 1 mΩ / I Z I
2.5 Ω
0.3% + 1 mΩ / I Z I
0,01 mΩ
20 Hz
Secondary parameters
Basic accuracy D, Q ±0,0001 if f = 1 kHz
Phase angle ±0,005° if f = 1 kHz
Ranges
|Z|, R, X 0,01 mΩ to 100 MΩ
|Y|, G, B 10 nS to 1.000 S
C 0,01 pF to 100 mF
L 10 nH to 100 kH
D 0,0001 to 9,9999
Q 0,1 to 9.999,9
θ -180° to +180 °
∆ -999,99 to 999,99 %
M 1 µH to 100 H
N 0,95 to 500
Measurement conditions and functions
Test frequency 20 Hz to 200 kHz (69 steps)
Frequency accuracy ±100 ppm
AC test signal level 50 mV
Resolution 10 mV
72
0.5% +
I Z I / 100 MΩ
0.1% +
I Z I / 1,5 GΩ
0.2% +
0.5% +
I Z I / 100 MΩ
5 mΩ / I Z I
+
0.2% +
I Z I / 10 MΩ
2 mΩ / I Z I
0.5% +
2 mΩ / I Z I
1 kHz 10 kHz 100 kHz
to 1.5 V
rms rms
rms
Drive level accuracy ±(5 % + 5 mV)
Internal bias voltage 0 V
Resolution 10 mV
External bias voltage 0 V
Internal bias current 0 mA to +200 mA
Resolution 1 mA
Range selection Auto and Hold
Trigger Continuous, manual or external via interface,
binning interface or trigger input
Trigger delay time 0 ms to 999 ms in 1 ms steps
Measurement time (f ≥1 kHz)
FAST 70 ms
MEDIUM 125 ms
SLOW 0.7 s
Miscellaneous
Test signal level monitor Voltage, current
Error correction Open, short, load
Save/Recall 9 instrument settings
Front-end protection
V
max
(1 Joule of stored energy)
Low potential and
low current guarding Ground, driven guard or auto (fused)
Constant voltage mode (25 Ω source)
Temperature effects R, L or C ±5 ppm/°C
Interface Dual interface USB/RS-232 (R&S®HO820),
optional R&S®HO880 IEEE-488 (GPIB)
Safety Safety class I (EN61010-1)
Power supply 110 V to 230 V ±10 %, 50 to 60 Hz, CAT II
Power consumption approx. 20 W
Operating temperature +5 °C to +40 °C
Storage temperature -20 °C to +70 °C
Rel. humidity 5% to 80 % (non condensing)
Dimensions (W x H x D) 285 x 75 x 365 mm
Weight approx. 4 kg
Accessories supplied: Line cord, operating manual,
R&S®HZ184 4-terminal kelvin test cable, R&S®HZ188
4-terminal SMD component test fixture
Recommended accessories:
R&S®HO118 Binning interface
R&S®HO880 Interface IEEE-488 (GPIB),
galvanically isolated
R&S®HZ42 19" rackmount kit 2RU
R&S®HZ72 GPIB-cable 2 m
R&S®HZ181 4-terminal test fixture including shorting
plate
R&S®HZ186 4-terminal transformer test cable
to +5,00 V
DC DC
to +40 V (fused 0.5 A)
DC DC
√
< 2/C @ V <200 V, C in Farads
max