General Warnings - OEM MILLENIUM VALIDO Bedienungs- Und Wartungshandbuch

MILLENIUM VALIDO
General specifications and warning
Chapter 1

1.1 - GENERAL WARNINGS

- Before starting the oven, user shall carefully read this
handbook and be aware of both technical specifications
and control elements.
- User should be trained in the use of the oven.
- Before installing the oven, make sure the area the latter shall
be placed in is compatible with oven overall dimensions and
weight.
- In case of installation or removal of oven parts, only means
of lifting & handling being suitable for both weight and ge-
ometric characteristics of the part to be lifted/handled shall
be utilized.
- Only authorized as well as trained personnel may start,
adjust and/or repair the oven.
Concerning operations to be carried out on the oven, please
refer to this handbook.
- Mechanical and electric parts being inside the oven are
protected by panels which are totally closed by means of
screws.
- Before carrying out cleaning and/or maintenance operations
as well as removing any protection, make sure the cutout
switch is on "OFF" (O), in order to disconnect power supply
to the oven during userʼs operation.
- Buyerʼs power supply system shall be equipped with an
automatic release system on the upper side of the oven
cutout switch and also with an earthing system complying
with all accident prevention protection requirements.
- In case of repairs to be done on the main switch or in the
main switch area, turn off the power of the electrical line.
- Any inspection and maintenance works requiring the removal
of the safety protections are made under the responsibility
of the user.
Therefore it is recommended that the above mentioned
works are done by authorized and skilled personnel
only.
- Make sure that all safety devices (barriers, protections,
carter, micro-switches, etc.) have not been tampered and are
perfectly working. On the contrary, they should be repaired.
- Do not remove the safety devices.
- In order to avoid personal risks, only suitable tools should
be used, in accordance with the local safety regulations.
- Do not tamper the electric and pneumatic plant or any other
mechanism for any reason.
- The oven shall not be left unguarded.
- Wear safety clothing only, approved by the law in force.
- In case of works to be done in a position that cannot be
reached from the ground, use safe ladders or lifting devices
only, in conformity with the local safety regulations.
- In case of repairs to be carried out near or under the oven,
make sure:
• there are no elements which can be started and/or there
are no unstable parts on or near the oven.
- To carry out operations on the oven, do not use your hands,
but only appropriate tools.
- Do not use your hands or other tools to stop any moving
parts.
- Do not use household matches, lighters or free flames near
the oven.
- TAKE HIGHEST CARE TO THE WARNING PLATES BEING
ON THE OVEN, WHEN YOU ARE GOING TO CARRY OUT
OPERATIONS ON OR NEAR IT.
- The user is obliged to keep all the warning plates in legible
conditions and, if required, to change their position in order
to make them fully visible to the operator.
- Moreover the user is obliged to replace any warning plate
that, for any reason, has been damaged or is not clearly
legible. New warning plates can be obtained through our
Technical Service Centre.
- It is strictly forbidden to carry out repairs when the oven
is functioning.
- In case of malfunctioning of the oven or damaged oven
components, please contact the person in charge of main-
tenance, without carrying out arbitrary repairs.
- It is strictly forbidden to make an improper use of the
oven.
The oven shall always be used as provided for by good,
scrupulous technique rules, according to 89/392 EEC di-
rection as well as workersʼ health & safety standards as per
legislation being in force in the oven utilization Countries
or, in the event the latter do not exist, according to 89/391
EEC direction.
- The manufacturer declines all responsibility for any
injury or damage to persons or things arising from inob-
servance of the safety regulations and the instructions
contained in this manual.
EN - 3