Using Delay-Start Function; Keep-Warm Mode; Using Several Steam Trays - Silvercrest SDG 800 A1 Bedienungsanleitung

Initial Operation
cess gets stopped. The indicator on the LCD-
display switches back to the time indicator
13
again (see Fig. A). Therefore, regularly
20
check the water level on the water level indica-
tor and replenish sufficient water in good time!
12
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
MAX mark . Otherwise, hot water may spurt
19
out of the steamer during operation.

Using Delay-Start Function

Q
Note: Consider that the base of the appliance /
water tank has to be filled with water at least up
10
to the MIN mark . Ensure that the turbo ring
9
as well as the condensate collection basin
positioned correctly.
P ress the PROG button
the time indicator
20
bol (see Fig. A) will appear.
21
P ress the PLUS / MINUS button
the delay time in 10-minute steps or decrease it
in 1-minute steps to achieve the desired delay.
Note: The set delay time refers to the current
clock time. That means if you set a delay time
of 30 minutes at 13:00, the steaming process
will start at 13:30. The maximum delay time is
24 hours.
P ress the PROG button
P ress the PLUS / MINUS button
the steaming time in 5-minute steps or decrease
it in 1-minute steps.
Note: The maximum steaming time is 90 minutes.
Note: Be aware that you might have to replen-
ish water when the steaming time is longer. Use
the openings on the sides of the condensate
collection basin
7
the appliance / water tank
the MAX mark , it will be sufficient for approx.
19
1 hour of steaming.
P ress the PROG button
display the time indicator
13
PROG symbol
21
is now activated.
I f the set delay time is elapsed, a signal tone
will sound, the pilot lamp
10 GB
7
. In the LCD-display
17
as well as the PROG sym-
, to increase
16
again.
17
to increase
16
for refilling. If the base of
is filled up to
10
again. In the LCD-
17
as well as the
20
will appear. The delay-start
will glow red and
15
the appliance will start the steaming process
automatically.
ATTENTION! HAZARD OF BURNS!
The appliance will become hot during use.
Beware of getting in contact with the ascending
steam or any components.
Note: The device starts to beep as soon as
the water in the reservoir is exhausted. The
steaming process is interrupted. Check the
water level in the reservoir regularly by referring
to the water level indicator
water in good time.
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
MAX mark
out of the steamer during operation.
8
are P ress the PROG button
delay start. The PROG symbol
display
13
,
13

Keep-Warm Mode

Q
If the steaming time is elapsed, the appliance will
automatically switch over to keep-warm mode.
- In the LCD-display
well as the keep-warm symbol
- The pilot lamp
- The water is heated repeatedly in cycles in
the warm mode to keep the food warm at a
temperature of approx. 60–70 °C.
ATTENTION! HAZARD OF BURNS! The
appliance will become hot during use. Beware
of getting in contact with the ascending steam
or any components.
- The keep-warm mode will remain active until
the supply of water is used up or you press a
button.
P ress the ON / OFF button
keep-warm mode.

Using Several Steam Trays

Q
Place the largest items of food or those with the
longest steaming time into the bottom steaming
basket .
6
and add more
12
. Otherwise, hot water may spurt
19
to terminate the
17
in the LCD-
21
will go out.
the time indicator
13
will appear.
22
will glow green.
15
to terminate the
14
as
20