Siemens SINAMICS Handbuch Seite 616

n_ist glatt Meld [1/min]
[8010.3] r2169
+
HLG Sollw am Eing [1/min]
[3050.8] r1119
–
0
-1
n_ist [1/min]
r0063
Vdc Schwellwert
p2172
Vdc Istw [V]
r0070
<1> [6730.1], [6731.1]
<3> [6841.1], [6842.1]
<2> [6856.1]
M_ist_filt T
0 ... 1000000 [ms]
p3233 [D] (100)
I_ist Betrag [Aeff]
r0068 [0]
<1> [6714.8]
<3> [6833.8]
<2> [6856.1]
0
U_Ausgang [Veff]
r0072
0
<1> [6730.4], [6731.4]
<3> [6841.4], [6842.4]
<2> [6856.4]
<1> p0096 = 0: Expert
<2> p0096 = 1: Standard Drive Control (SDC)
<3> p0096 = 2: Dynamic Drive Control (DDC)
<4> Berechnet.
1 2
Signale und Überwachungsfunktionen
Überwachungsfunktionen 1
0
1
0
<4>
1
2.00 [1/min]
Hysteresedrehzahl 3
1
0
I_schw
p2170
1
0
1
p0305 • 3%
Impulsfreigabe
1
0
3 4
n_min
p1080
1
0
<4>
2.00 [1/min]
Hysteresedrehzahl 3
n_still n_schw
Impulslösch t_Ver
p1226
p1228
1
T 0
0
10 ms
T 0
10 ms
T 0
1
I_schw err t_ver
p2171
0 T
I_schw
I_schw err t_ver
p2170
p2171
1
0 T
0
2000 ms
T 0
5 6
fp_8022_97_05.vsd
07.12.2015
r2197
r2197.0
r0053 1 = |n_ist| ” n_min p1080
1
r0053.2
[2511.6]
r2197
r2197.4
r0053
1 = |n_ist| • n_soll
r0053.6
[2511.6]
r2197
r2197.5
r0053
1 = |n_ist| ”
1
r0053.1
n_stillstand p1226
[2511.6]
r2197
r2197.9
r0053 1 = Vdc_ist ”
Vdc_schwellwert p2172
r0053.7
[2511.6]
r2197
r2197.10
r0053
1 = Vdc_ist >
r0053.8
Vdc_schwellwert p2172
[2511.6]
r2197
r2197.8
r0053
1 = I_ist •
r0053.3 I_schwellwert p2170
[2511.6]
r2198
r2198.8
1 = |I_ist| <
I_schwellwert p2170
Antrieb: Kein Motor erkannt
A07929
r2197
r2197.11
1 = Ausgangslast nicht
vorhanden
7
Funktionsplan
SINAMICS G120C
V4.7.6
[2534.2]
[2534.2]
[2534.2]
[2534.2]
[2534.2]
[2534.2]
[2536.2]
[2534.2]
8
- 8022 -