Siemens SINUMERIK 828D Inbetriebnahmehandbuch Seite 9

6.6 High Speed Settings (Advanced Surface) .................................................................................182
6.6.1 Funktion High Speed Settings (CYCLE832) konfigurieren........................................................182
6.6.2 So passen Sie die Funktion High Speed Settings (CYCLE832) an...........................................184
6.7 Messzyklen und Messfunktionen ...............................................................................................186
6.7.1 Allgemeine Einstellungen zum Messen .....................................................................................186
6.7.2 Hersteller-Zyklus CUST_MEACYC.SPF....................................................................................189
6.7.3 Messen in der Betriebsart JOG..................................................................................................189
6.7.4 JOG: Werkstück messen in Fräsen ...........................................................................................191
6.7.5 JOG: Werkzeug messen in Fräsen............................................................................................193
6.7.6 JOG: Werkzeug messen in Drehen ...........................................................................................197
6.7.7 Messen in der Betriebsart AUTOMATIK....................................................................................198
6.7.8 AUTO: Allgemeine Einstellungen zum Werkstückmessen ........................................................200
6.7.9 AUTO: Werkstück messen in Fräsen ........................................................................................202
6.7.10 AUTO: Werkstück messen in Drehen........................................................................................204
6.7.11 AUTO: Werkzeug messen in Fräsen .........................................................................................205
6.7.12 AUTO: Werkzeug messen in Drehen (CYCLE982) ...................................................................213
7 Service Planner ..................................................................................................................................... 215
7.1 PLC-Anwenderprogramm ..........................................................................................................217
7.2 Schnittstellen im PLC-Anwenderprogramm...............................................................................218
7.3 Funktionen am HMI....................................................................................................................223
8 Easy Extend .......................................................................................................................................... 231
8.1 Funktionsübersicht.....................................................................................................................231
8.2 Projektierung im PLC-Anwenderprogramm ...............................................................................233
8.3 Darstellung auf der Bedienoberfläche .......................................................................................235
8.4 Sprachabhängige Texte erstellen ..............................................................................................236
8.5 Beschreibung der Skript-Sprache ..............................................................................................237
8.5.1 Sonderzeichen und Operatoren.................................................................................................238
8.5.2 Aufbau des XML-Skripts ............................................................................................................239
8.5.3 CONTROL_RESET....................................................................................................................241
8.5.4 DATA..........................................................................................................................................241
8.5.5 DATA_ACCESS .........................................................................................................................241
8.5.6 DATA_LIST ................................................................................................................................242
8.5.7 DRIVE_VERSION ......................................................................................................................243
8.5.8 FILE............................................................................................................................................244
8.5.9 FUNCTION.................................................................................................................................245
8.5.10 FUNCTION_BODY ....................................................................................................................246
8.5.11 INCLUDE ...................................................................................................................................248
8.5.12 LET.............................................................................................................................................248
8.5.13 MSGBOX ...................................................................................................................................250
8.5.14 OP ..............................................................................................................................................251
8.5.15 OPTION_MD ..............................................................................................................................252
8.5.16 PASSWORD ..............................................................................................................................253
8.5.17 PLC_INTERFACE......................................................................................................................253
8.5.18 POWER_OFF.............................................................................................................................254
8.5.19 PRINT ........................................................................................................................................254
8.5.20 WAITING....................................................................................................................................255
8.5.21 ?up .............................................................................................................................................256
8.5.22 XML Bezeichner für den Dialog .................................................................................................256
8.5.23 BOX............................................................................................................................................258
8.5.24 CONTROL..................................................................................................................................258
Drehen und Fräsen
Inbetriebnahmehandbuch, 09/2009, 6FC5397-3DP20-0AA0
Inhaltsverzeichnis
9