Herunterladen Diese Seite drucken

Atlas Copco R2012 Produktspezifische Anweisungen Seite 5

Air hydraulic riveter

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 11
R2012
• All hydraulic connections must be securely connected.
Loose or improper threaded fittings can be potentially
dangerous if pressurized. Severe over tightening can
cause premature thread failure. Fittings need to be only
securely tightened and leak free.
• Ensure quick-disconnect couplings are clean and
fully engaged.
• Threaded connections such as fittings, gauges etc.
must be clean, securely tightened and leak-free.
• Do not use kinked hoses. Inspect and replace if damaged.
• Protect hoses and connectors from hazards such as sharp
edges, heat or impacts. Inspect daily and replace if
cracked, worn, damaged or leaking.
Service and Maintenance
General Service and Maintenance Safety
• Always disconnect the tool from the compressed air sup-
ply when carrying out maintenance work and when the
tool is not in use.
• Store the tool in a dry place protected from frost.
• Regularly maintain the complete grip mechanism.
• Regularly empty the stem collector. Overfilling will
cause the tool to malfunction.
• Regularly check the compressed air lines to ensure that
they are fitted correctly and airtightly.
• Repairs must be carried out only by skilled personnel. In
case of doubt, always send in the complete tool (not dis-
assembled) to the supplier or to Atlas Copco.
• Replace worn nose pieces if necessary.
• Regular maintenance will extend the service life of your
high-quality tool. Service the tool at least every 2 years
by an authorised workshop or by Atlas Copco Service.
Service the tool ahead of schedule is it is subject to inten-
sive use.
• Repairs under warranty are carried out by the manufac-
turer. Repairs outside the warranty period should only be
carried out by skilled technical personnel. Failure to ob-
serve the assembly and setting procedures and operation
by non-skilled personnel may result in serious damage to
the tool. In case of doubt, always send the tool back to the
supplier or to Atlas Copco.
• Refill or replace the hydraulic oil after prolonged use.
• Dispose of the used hydraulic oil in accordance with valid
environmental protection regulations.
General Safety Instructions
Additional safety information regarding portable air
tools:
• CAGI 2528 - B186.1, SAFETY CODE FOR POR-
TABLE AIR TOOLS, available from Global Engi-
neering Documents at https://global.ihs.com/ or call
+1 800 447-2273. In case of difficulty in obtaining
ANSI standards, contact ANSI via https://
www.ansi.org/
© Atlas Copco Industrial Technique AB - 9846 0527 00
Air supply and connection hazards
• Air under pressure can cause severe injury.
• Always shut off air supply, drain hose of air pressure and
disconnect tool from air supply when not in use, before
changing accessories or when making repairs.
• Never direct air at yourself or anyone else.
• Whipping hoses can cause severe injury. Always check
for damaged or loose hoses and fittings.
• Do not use quick disconnect couplings at tool. See in-
structions for correct set up.
• Whenever universal twist couplings are used, lock pins
must be installed.
• Do not exceed maximum air pressure of 6.3 bar / 90 psig,
or as stated on tool nameplate.
• Never carry an air tool by the hose.
Hydraulic supply and connection hazards
• Do not exceed the maximum relief-valve setting stated on
the tool.
• Carry out a daily check for damaged or worn hoses or hy-
draulic connections and replace if necessary.
• Use only clean oil and filling equipment.
• Power units require a free flow of air for cooling pur-
poses and should therefore be positioned in a well-venti-
lated area free from hazardous fumes.
• Ensure that couplings are clean and correctly engaged be-
fore operation.
• Do not inspect or clean the tool while the hydraulic
power source is connected. Accidental engagement of the
tool can cause serious injury.
• Do not install or remove the tool while the hydraulic
power source is connected. Accidental engagement of the
tool can cause serious injury.
• Be sure all hose connections are tight.
• Wipe all couplers clean before connecting. Failure to do
so can result in damage to the quick couplers and cause
overheating.
Entanglement hazard
• Keep loose articles of clothing, long hair and cleaning
materials away from the tool when in use.
• Do not wear jewellery or loose clothing.
Projectile hazards
• Always shut off air supply, relieve hose of air pressure
and disconnect tool from air supply when changing ac-
cessories.
• Failure of the workpiece, accessory, retainer or even of
the tool itself could generate high velocity projectiles.
Even small projectiles can injure eyes and cause blind-
ness.
• Always wear impact-resistant eye and face protection
when involved with or near the operation, repair or main-
tenance of the tool or changing accessories on the tool.
• Be sure all others in the area are wearing impact-resistant
eye and face protection.
• Ensure that the workpiece is securely fixed.
Safety Information
5

Werbung

loading

Diese Anleitung auch für:

8426201200