EINHELL TC-SB 200 + Originalbetriebsanleitung Seite 24

machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Mains voltage: ......................... 220-230 V ~ 50 Hz
Power: ........................S1 250 W · S6 20% 300 W
Idle speed n : ......................................1400 min
0
Blade: ................................... 1405 x 7 x 0.37 mm
Tooth pitch in teeth per 25.4mm:
..............................................6 tpi (teeth per inch)
Blade length min. - max.: ............. 1395-1415 mm
Blade width min. - max.: ........................ 6-13 mm
Blade speed V: ....................................900 m/min
Cutting height: .................................. 80 mm / 90°
.......................................................... 45 mm / 45°
Reach: .................................................... 200 mm
Table size: ..................................... 305 x 305 mm
Tilting range of table: ............................ -2° to 45°
Workpiece size: ..................... 400 x 400 x 80 mm
Dust extraction connector: ....................Ø 36 mm
Protection class: ................................................. I
Weight: .....................................................16.3 kg
Operating mode S6 20%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot it is
allowed to be operated for only 20% of the cycle
at the specifi ed rating and then must be allowed
to idle for 80% of the cycle.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
Operation
L sound pressure level ........................ 71 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ........................... 84 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
Anl_TC-SB_200_PLUS_SPK13.indb 24 Anl_TC-SB_200_PLUS_SPK13.indb 24
GB
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
-1
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be con-
sidered (for example, times in which the electric
tools are switched off and times in which the tool
is switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
5. Before using for the fi rst time
Make sure the machine stands securely, i.e. bolt it
to a workbench or solid base.
•
The saw table must be correctly fitted.
•
All covers and safety devices must be proper-
ly fitted before the machine is switched on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been previ-
ously processed, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
- 24 -
19.12.2023 10:24:41 19.12.2023 10:24:41