EINHELL TC-SB 200 + Originalbetriebsanleitung Seite 26

tilt angle of the upper blade pulley (8) must be
corrected.
•
Slacken the wing handle (30) in order to be
able to turn the adjustment handle (29).
•
If the blade (26) runs more towards the rear of
the blade pulley (8), i.e. towards the machine
frame (25), the adjustment handle (29) must
be turned counter-clockwise. Then turn the
blade pulley (7) slowly with the other hand to
check the position of the blade (26).
•
If the blade (26) runs towards the front of the
blade pulley (8), the adjustment handle (29)
must be turned clockwise.
•
Secure your adjustment on the upper blade
pulley (8) by tightening the wing handle (30).
•
Close the two side covers (12). Push the side
cover against the machine frame (25) as far
as it will go. The side cover must latch home
with an audible click. Screw the fastening
handle (13) tight with the side cover (12) held
in pressed position.
5.4 Adjusting the support bearing (Fig. 7-10)
•
Each time after changing the blade you must
readjust the support bearings and the lateral
guide pins at the lower and upper blade gui-
de.
•
Important! Before adjusting the support bea-
rings you must adjust the blade tension as in
5.2 and the position of the blade (26) on the
pulleys as in 5.3.
•
Important! The support bearings the lateral
guide pins support the blade (26) only during
the cutting operation. The blade should not
touch the support bearings/guide pins in id-
ling mode.
•
To open the grub screws described below you
can use the 2.5 mm hex key (2), to open the
socket head screws you can use the 4 mm
hex key (28).
5.4.1 Adjusting the upper support bearings
(Fig. 7/8)
•
Adjust the upper blade guide (11) to medium
height (see 5.5).
•
Slacken the grub screw nut (40) in order to
release the support bearing (39).
•
Begin by adjusting the position of the lateral
guide pins (37) relative to the blade (26). To
do so, slacken the grub screw (42) in order to
be able to move the upper bearing unit (41).
The guide pins (37) should be approx. 1 mm
behind the gullet of the blade (26).
Anl_TC-SB_200_PLUS_SPK13.indb 26 Anl_TC-SB_200_PLUS_SPK13.indb 26
GB
•
Caution! The blade will be rendered useless
if the teeth touch the guide pins while the bla-
de is running!
•
Fasten the position of the bearing unit (41)
again with the grub screw (42).
•
Now adjust the distance between the support
bearing (39) and the rear of the blade (26).
Push the support bearing (39) forward until
it just fails to touch the blade (leave a gap of
approx. 0.5 mm).
•
Fasten the position of the support bearing
(39) again with the grub screw (40).
•
Finally, adjust the distance of the two lateral
guide pins (37) from the blade (26). To do so,
slacken the grub screws (38) and push the
guide pins (37) toward the blade (26) until
they just fail to touch the blade (leave a gap of
approx. 0.5 mm).
•
Fasten the position of the guide pins (37) with
the grub screws (38).
5.4.2 Adjusting the lower support bearings
(Fig. 9/10)
•
Disassemble the saw table (15). (See 5.1.)
•
Open the lower side cover (12) by slackening
the fastening handle (13).
•
Begin by adjusting the position of the lateral
guide pins (43) relative to the blade (26). To
do so, slacken the socket head screw (45) in
order to be able to move the lateral guide pins
(43). The guide pins (43) should be approx. 1
mm behind the gullet of the blade (26).
•
Caution! The blade will be rendered useless
if the teeth touch the guide pins while the bla-
de is running!
•
Fasten the position again with the socket
head screw (45).
•
Now adjust the distance between the support
bearing (46) and the rear of the blade (26).
Slacken the socket head screw (47) and push
the support bearing (46) forward until it just
fails to touch the blade (leave a gap of approx.
0.5 mm).
•
Fasten the position of the support bearing
(46) again with the socket head screw (47).
•
Finally, adjust the distance of the two lateral
guide pins (43) from the blade (26). To do so,
slacken the grub screws (44) and push the
guide pins (43) toward the blade (26) until
they just fail to touch the blade (leave a gap of
approx. 0.5 mm).
•
Fasten the position of the guide pins (43) with
the grub screws (44).
•
Close the side cover (12) again.
- 26 -
19.12.2023 10:24:42 19.12.2023 10:24:42