Proper Use; Technical Data - EINHELL TE-MB 18/127 Li Originalbetriebsanleitung

3. Proper use

The cordless bandsaw is designed for cutting
sawn timber and wood-type materials, non-tem-
pered metals and non-ferrous metals. The cord-
less bandsaw is not designed for cutting fi rewood.
No reactive or poisonous materials are allowed
to be processed. Take care not to overload the
machine.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
General safety information
It is the user's responsibility to install and use
the machine properly in accordance with the
instructions issued by the manufacturer. If elec-
tromagnetic interference is noticed, it is the user's
responsibility to eliminate said interference with
the technical devices mentioned in the section
„Important information about the power connec-
tion".
Only blades suitable for the machine are allowed
to be used. To use the machine properly you must
also observe the safety information, the assembly
instructions and the operating instructions to be
found in these operating instructions.
All persons who operate and service the machine
must be acquainted with these instructions and
must be informed about potential hazards. It is
also imperative to observe the accident preven-
tion regulations in force in your area. The same
applies for the general rules of health and safety
at work.
The manufacturer will not be liable for any chan-
ges made to the machine nor for any damage
resulting from such changes.
Even when the machine is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards might arise in
connection with the machine's construction and
design:
Anl_TE_MB_18_127_Li_SPK13.indb 19 Anl_TE_MB_18_127_Li_SPK13.indb 19
GB
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.
•
Risk of accident through hand contact with
the blade in the uncovered cutting zone.
•
Risk of injury when changing the blade (risk
of cuts).
•
Injuries from catapulted workpieces or parts
of workpieces.
•
Crushed fingers.
•
Injuries from kickback.
•
Tilting of the workpiece due to inadequate
support.
•
Touching the blade.
•
Dust and splinters can cause eye injuries. For
this reason you must always wear safety gog-
gles or spectacles with safety lenses.
•
Dust presents a special danger. You should
wear a suitable safety mask so that you are
not forced to breathe in any dust.
•
Always wear tight-fitting protective clothing
that is in perfect condition.
•
Long hair must be tied together, loose jewelry
should not be worn.
•
The workpiece you want to cut must always
be clamped securely. The workpiece must be
shaped so that it can be clamped securely.

4. Technical data

Motor power supply: ............................... 18 V DC
Idle speed: ............................................240 min
Blade speed: .......................................120 m/min
Blade: ................................ 1141 x 13 x 0.65 mm
Tooth pitch in teeth per 25.4 mm: ........................
.......................................10/14 tpi (teeth per inch)
Max. cutting width: ................................. 127 mm
Maximum cutting height: ........................ 115 mm
Protection class: ........................................III /
Weight: ............................................ approx. 6 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ........................ 86 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ........................... 99 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
- 19 -
-1
13.09.2022 14:38:57 13.09.2022 14:38:57