Denon AVC2530 Bedienungsanleitung Seite 9

BASS control
Use this to adjust the bass sound of the front speaker
output or PRE-OUT FRONT jacks. The bass sound is
emphasized when turned clockwise ( ™ ) from the
center position, reduced when turned counterclock-
wise (©) ) from the center position.
TREBLE control
Use this to adjust the treble sound of the front
speaker output or PRE-OUT FRONT jacks. The treble
sound is emphasized when turned clockwise ( © )
from the center position, reduced when turned
counterclockwise (©) ) from the center position.
BALANCE control
Use this to adjust the left/right balance of the front
speakers (PRE-OUT FRONT jacks).
VIDEO AUX INPUTS
These are auxiliary inputs for connecting camcor-
der's or video cameras or other AV equipment.
S-VIDEO: Connect the S-jack output of the other
component here.
Connect the video output of the other
component here. (Use a 75 ohm video
coaxial cable pin-plug cord.)
AUDIO L and R: Connect the audio output of the
other component here.
VIDEO:
DAT/TAPE MONITOR
This button is used to play the audio signals input
from the component connected to the DAT/TAPE-1,
DAT/TAPE-2 jacks on the rear panel over the speak-
ers, or to monitor the sound which was actually
recorded on a three-head tape deck.
When the button is pressed once, the DAT/TAPE
monitor mode is set. When the button is held in, the
DAT/TAPE input signal changes in the order shown
below. Release the button when the desired DAT/
TAPE input signal is displayed on the MFD.
ee DAT/TAPE-1 ————> DAT/TAPE-2 ae
SOURCE
When the DAT/TAPE monitor mode is set, the audio
(video) signals selected with the VIDEO or AUDIO
FUNCTION button are output to the VCR's video REC
OUT jacks and the REC OUT jacks of the DAT/tape
deck which is currently being monitored.
NOTE
e The mode automatically switches to the bypass
mode when using the tape monitor function in the
Hi-Vision mode.
e@ The DAT/TAPE MONITOR button will not function
when the CD direct function is selected.
©
®eee8 ee
@
GND (Grounding terminal)
The grounding wire of the turntable is connected
here.
e Hum or noise may be generated if the grounding
wire is not connected.
AUDIO IN (audio input) jacks
HI-VISION IN jacks
Refer to page 7.
AUDIO OUT (audio output) jacks
VIDEO (video input/output) jacks
S-VIDEO (video input/output) jacks
PRE OUT
(FRONT, CENTER, REAR and MONO) jacks
Refer to page 6.
Connect the monaural audio input jack of a separate-
ly sold subwoofer or TV here.
REAR SPEAKER SYSTEMS terminals
FRONT SPEAKER SYSTEMS terminals
CENTER SPEAKER SYSTEMS terminals
Note on the center speaker terminals:
The center channel output on the AVC-2530 is
dual center compatible, so two center speakers
can be used.
For details, refer to pages 4 and 6.
AC cord (power cord)
=® Continued
Display @
al
dB
(ld ms
CT (00) [DOLBY SURROUND]
PRO- LOGIC
@ sV. SELECT (VIDEO INPUT SELECT indicator)
This indicator lights when the video monitor output
is fixed in the video input select mode.
@ MULTI FUNCTION DISPLAY
This displays a maximum of 9 characters.
Normally the reception frequency is displayed when
the function is set to tuner, and the surround mode is
displayed when the function is set to other positions. ©
The display also indicates various other information
according to the buttons pressed, as shown in the
examples on the pages 9 to 10.
DOLBY SURROUND Indicator
This indicator lights when DOLBY PRO LOGIC is
selected by pressing the SURROUND MODE button.
Multi-function Display (MFD)
The multi-function display indicates the status of the mode which has been operated by pressing the buttons on the front
panel or on the remote control unit.
Display pattern examples
1. When the power is turned on
(1) The function name is displayed.
(2) The surround mode name is displayed.