Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ON-SCREEN DISPLAY
If the SCREEN button on the remote control unit is pressed when the power is turned on, the operating modes are
displayed on the monitor TV's screen
when
buttons are operated, etc.
The displays shown below appear on the screen when the power is turned on and the SCREEN button is operated. The
mode
changes
between
screen
1, screen
2, screen 3, screen
4 and off each time the SCREEN
button is pressed.
When the power is turned on, screens 1 to 3 are displayed for approximately 6 seconds, after which the on-screen display
automatically turns off.
.
When
other buttons are pressed, messages
related to the button that was pressed are displayed for approximately 5
seconds, then automatically turn off.
(The normal picture is displayed under the message, but if no picture is being input, the background turns a color which is
internally produced.)
NOTE
e The on-screen
display signals are not output to
the S-VIDEO MONITOR
OUT jacks or the video
If a video source is selected but no video signals are
being input (when a color background is displayed),
the color background turns off after the message is
displayed.
output jacks for recording.
- The following screens are examples of displays.
Screen
1 Surround
mode
display
@ Surround mode
@Center mode
QA.V.S.E. setting (on/off)
DENON
AV SURROUND
AMPLIFIER
@Cinema setting (on/off)
* DOLBY
PRO LOGIC
ame
Te
©) Output indicators
[NORMAL]
@
These indicators are displayed when signals are being
*
EQ
*
|
output to these channels.
A.V.S.E.
>>> PP ION]
@
CINEMA
>>>
PP PP ION]
@
* OUTPUT *
|
FRONT
CENTER
REAR
———©)
Screen 2 Level display, etc.
@Test tone display
*
TO]
*
This is displayed when
the test tone mode
is set.
T.TONE
[AUTO]
Oc
enter level
Fee
nS
@
The level is displayed by a bar graph and by the decibel
*
LEVEL/DELAY
*
(dB) value.
CENTER Samm cece
~20dB
@
If the level is increased, the bar becomes longer.
REAR
Me
-14d8
——@
@Rear level and balance
DELAY TIME
21.0msec
|
@
The levels are displayed
by a bar graph and by the
decibel (dB) value.
If the level is increased, the bar becomes
longer.
@ Delay time
This displays the delay time.
Screen 3 Input/output display
* INPUT *
VIDEO
AUDIO
D/T MONITER
* VCR REC *
4
4
<
VIDEO
4
<
4
<
AUDIO
* D/TAPE
REC *
D/TAPE1
D/TAPE2
eeowew
men
ewe
Screen 4 Parameter display, etc.
* PARAMETER
*
SURR.
SIGNAL
>
L-R
ADAPTIVE
MATRIX
7kHz L.P.F.
SOUND
SIM.
ROOM
SIZE
EFFECT LEVEL
ON
ON
ON
10
vvvvv
Other
1
* MUTING
*———————-—-@®
Other 2
* PROTECTION?
* 1
@ Input selector display
The set input is displayed
here.
@VCR recording output selector display
The name
of the source being output to the VCR is
displayed
here.
@DAT/TAPE
recording output selector display
The name of the source being output to the DAT/TAPE-
1 and DAT/TAPE-2
jacks is displayed here.
@ Parameter display
.
This indicates the DSP parameters.
Displayed for approximately
15 seconds.
NOTE
The parameters displayed at section ":*1" of Screen
4 are only displayed on the screen and cannot be set.
However,
when
the "SURR.
SIGNAL"
setting
is
switched from "L — R" to "L +R", the "ADAPTIVE
MATRIX" display automatically switches from "ON"
to "OFF".
@Muting display
This flashes when
in the muting mode.
@ Protection circuit display
This flashes when
the protection circuit is activated.
For details, refer to page 22.
21
Werbung
