Werbung
Verfügbare Sprachen
Verfügbare Sprachen
@
Tuner system buttons
With
these
buttons,
a Denon
remote
controllable
tuner can be controlled directly.
For details, refer to the tuner's operating instruc-
tions. Note that operation may not be possible for
some
models.
[ & |: Preset (preset channel up)
[ w_]:
Preset (preset channel down)
@®
DAT system
buttons
With these buttons,
a Denon
remote
controllable
DAT can be controlled directly.
For details, refer to the DAT's operating instructions.
Note that operation may not be possible for some
models.
[>]:
Play
[ i |: Pause
[m |: Stop
[ e |: Record
[4] and [>>]: Manual search (reverse and for-
ward)
[i€q] and [DPI]: Auto search (reverse and for-
ward)
System Call Buttons
@
Tape deck system buttons
With
these
buttons,
a Denon
remote
controllable
tape deck can be controlled directly.
For details, refer to the tape deck's operating instruc-
tions. Note that operation may not be possible for
some
models.
: Forward
play
: Reverse
play
: Pause
: Stop
: Record
: Rewind
: Fast-forward
A/B}:
Switching between decks A and B for dou-
ble decks
BRAC
a
VCR system
buttons
No system
codes
are stored
here.
@
TV system
buttons
No system
codes
are stored
here.
The system call function is a function which allows you to store a series of remote control operations consisting of the
operations of up to a maximum
of ten buttons, then perform this series of operations by pressing a single button.
e Storing the System Call Operations
1. Press the
button.
The START
LED in the indicator section flashes.
2. Set the PROGRAM switch @ to the desired side, then
press the buttons for the system call operations in the
order you want to send the signals (up to a maximum of
ten buttons). The LEARNED/TX LED lights each time a
button
is pressed.
It is not possible to store the codes of more than ten
buttons.
If the button which
has been
pressed
is a
non-storable button or if an 11th button is pressed, the
START LED will turn off while that button is pressed.
'3. Press one of buttons{1jto [3] at which you want to store
the system
calli series.
4. The START LED turns off. The system call series has
now
been
stored.
5. Three system
call series can be stored, one each at
buttons [1] to [3].
To continue storing another series, repeat steps 1 to 4.
NOTE:
Signals are sent from the remote control unit
when
buttons
are
pressed
while
storing
the
system call series, so prevent the components
from operating by covering the transmitting-win-
dow, etc.
Clearing the System
Call Series
. Press the
button. The START LED starts flashing.
. Press the button, [1] to
[ 3 ] , which you want to clear.
. The START LED turns off and the system call series is
cleared.
. To clear another button, repeat steps 1 to 3.
Using the System
Call Buttons
. Press the desired
button, [1] to [3], once.
. The LEARNED/TX
LED lights, and the remote control
codes are sent in the order in which they were stored at
a speed of approximately
one second
per code.
. The LEARNED/TX LED turns off once all the codes have
been
sent.
Remote
Control Unit Learning
Function
Follow the procedures
explained
below to use the remote
control unit's learning function.
e Operation
1. Press the USE/LEARN
(normal use/learn mode) selec-
tor button ® with the tip of a pen, etc., to set the learn
mode. Both the START and LEARNED/TX indicators in
the indicator section @ flash, indicating that codes can
be "learned".
2. Set the PROGRAM switch @ to the desired side, AMP or
AV.
3. Point the heads (transmitting window) of the RC-163
and the other remote control unit at each other at a
distance
of approximately
5cm.
4. Press the button on the RC-163 at which you want to
store the code for one or two seconds, then release it.
The
LEDs
stop flashing,
and
only the START
LED
remains
lit.
(If a non-learnable button is pressed or if two or more
buttons are pressed, both the LEDs will stop flashing,
remaining
lit, when
the button(s)
is (are) released.)
5. Check that the START LED @ is lit, then press in the
button on the other remote control unit whose code
you want to store in the RC-163.
6. When the START LED @ turns off and the LEARNED
LED lights, release the button. That code is now stored.
Both LEDs once again start flashing. This operation can
now be repeated to store other codes in the RC-163.
NOTE:
e If the code was not stored in the RC-163, the
LEARNED
LED will light after the START
LED
turns off. For a very limited number of models,
codes cannot be stored in the RC-163.
If after the START
LED lights both LEDs start
flashing rapidly, this means
that the memory
is
full. The code you just tried to store in the RC-163
was not registered.
To store a different code at a certain button, first
used the "Resetting Procedure".
7. To store codes at other buttons, repeat steps 4 to 6.
8. After you finish storing all the codes you want, press
the
USE/LEARN
(normal
use/learn
mode)
selector
button © again. Both
LEDs stop flashing and the
sending (use) mode
is set.
Check that the stored codes work properly.
Learnable
buttons:
When
the PROGRAM
switch
is at
tMOAMP SidG fsesicsc'sstinsateived
secestacerap i auasias 14 buttons
When
the PROGRAM
switch is at
the AV Sige: «655 ciivatndesteeciaszectiisicetoveaceeas 58 buttons
Maximum
of 35 codes
in 72 buttons
NOTE:
Depending on the types of codes stored, it may not be
possible to store 35 codes.
e Resetting (Clearing) Procedure
1. Press the USE/LEARN
(normal use/learn mode) selec-
tor button ® with the tip of a pen, etc., to set the learn
mode.
2. Set the PROGRAM switch @ to the side whose codes
you want to clear, AMP
or AV.
3. Press the POWER
button @ and REAR w button ®
simultaneously,
and
hold them
in for at least four
seconds.
.4. When both the START and LEARNED
LEDs @ light
simultaneously, all the learned codes for the selected
source
are cleared.
e Remote Control Operation
1. Check that both the LEDs are off. If they are flashing or
lit, press the USE/LEARN
(normal
use/learn
mode)
selector button
@ so that the LEDs turn off.
2. When
a button
at which
a code was
"learned"
is
pressed, the LEARNED/TX
LED lights and the remote
control code is sent.
13
Werbung
