Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2.
Surround mode display
(3)
3.
5.
6.
Recording
output display
10
Center level display
Input display
(10)
(11)
(6)
(8)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
"DOLBY PRO LOGIC", "DOLBY 3CH LOGIC", "WD
SCREEN",
"LIVE",
"MNO
MOVIE",
"CLASSIC",
"ROCK", "CHURCH",
"JAZZ", "STADIUM",
"MAT-
RIX" or "BYPASS"
is displayed.
"NORMAL",
"PHANTOM"
or "WIDE"
is displayed.
* These are not displayed in modes not using the
Dolby center modes or when the adaptive matrix
is off in the WIDE
SCREEN
or LIVE modes.
The delay time is displayed.
*
The delay time is only displayed in the DOLBY
PRO
LOGIC, WIDE
SCREEN,
LIVE and MATRIX
modes.
"CNTR
VOL"
is displayed
when
the one
of the
CENTER
buttons is pressed.
The level is displayed in steps of 2dB, from —24dB
(minimum)
to 0dB (maximum).
NOTE:
This is not displayed in modes in which no signals
are output to the center speaker(s).
This is displayed when one of the REAR buttons is
pressed.
The level is displayed in steps of 2dB, from -—24dB
(minimum)
to 0dB (maximum).
NOTE:
This is not displayed in modes in which no signals
are output to the rear speakers.
This
is displayed
when
one
of the
FUNCTION
buttons (AUDIO or VIDEO) is pressed, and the name
of the function is displayed in section (10). "D/TAPE-
1" or "D/TAPE-2" is displayed if the TAPE MONITOR
button or the remote control unit's DAT/TAPE-1
or
DAT/TAPE-2
button is pressed. If the video signal
has already been selected with the VIDEO SELECT
button, the audio input and video input are displayed
for 3 seconds when the AUDIO FUNCTION button is
pressed.
This is displayed when
the REC SELECT
button is
pressed.
The
name
of the function
("VOP/DBS",
"VCR-1",
"VCR-2"", or "V-AUX")
is displayed.
Normally
the source
is displayed.
When the recording output selection function is off
and the video selection function is on, the source is
displayed
for the audio
output
and the selected
signal ("VDP/DBS", "VCR-1", "VCR-2", or "V-AUX")
is displayed for the video output.
7.
Test tone display
(13)
9.
Clear display
(14)
PNET
VT
Ae
13. No display (MFD off)
i
1
|
|
This is displayed when the T.TONE button on the remote
control unit is pressed.
(12)
The speaker from which the test tone is being output
is displayed
here.
This message is displayed until the test tone function
is turned off.
(13) The following are displayed in modes for which the
PARAMETER
key is effective:
"S.SIG"
"INITIAL
D."
"ROOM
SIZE"
"EFFECT (LEVEL)"
"EFFECT (ON/OFF)"
Also, "AVSE"
or "CINEMA"
is displayed when the
remote
control unit's AVSE
or CINEMA
button
is
pressed.
e
The parameter
settings are displayed
here.
This is displayed when the CLEAR
button is pressed.
"FRONT"
is displayed at section (14) when
the remote
control unit's FRONT button is pressed, "CNTR" when the
CENTER button is pressed, and "REAR" when the REAR
button is pressed. "ON" or "OFF" is displayed at section
(15).
This
is displayed
when
the
MUTING
button
on
the
included
remote
control
unit
is pressed,
and
remains
displayed until the muting function turns off.
This is displayed when the protection circuit is on. For
details, refer to page 22.
Use this when you do not need or do not want to use the
MFD.
When the PANEL key on the remote control unit is pressed
and held in, the display on the MFD changes continuously
and finally turns off. After this is done, when a button is
pressed, the corresponding
display appears
for several
seconds, but the MFD then automatically turns back off.
To turn the MFD back to the normal display mode, press
the PANEL button on the remote control unit once again.
Werbung
