Werbung
Verfügbare Sprachen
Verfügbare Sprachen
[4] PART NAMES AND FUNCTIONS
(Refer to the figures on page 3.)
POWER
switch
e ON
When this switch is pressed once, the power turns
on and the STANDBY
LED @ flashes. (The muting
circuit is activated while "MUTING"
is flashing to
prevent noise when the POWER switch is operated.)
After several seconds, the LED stops flashing, re-
maining lit and the muting circuit turns off. The set is
now in the normal operating mode.
e STANDBY
When the POWER switch is pressed once again, the
power turns off and the standby mode is set. The
STANDBY LED © remains lit. In addition, when the
power turns off, the power supply from the SWITCH-
ED AC outlets on the rear panel also turns off.
REC SELECT
(independent VCR recording output selector button)
This button is used to select the signals output to the
VCR-1
and VCR-2
video
and/or
audio
recording
output jacks, independent of the mode selected with
the function selector buttons.
When
this button
is pressed
once, the recording
select mode is turned on and off. If the button is held
in, the audio/video recording output switches in the
order shown
below. Release the button when the
desired audio/video
recording
output appears
on
the MFD @.
Press the REC SELECT button again to cancel this
mode.
VDP/DBS ———> VCR-1 ———» VCR-2
eee
SOURCE «————— V-AUX panes
NOTE:
e if the "V-AUX"
inputs is selected with the REC
SELECT mode when the AUDIO function has been
selected, the VIDEO AUX video signals are output
to the monitor.
e 'Ifthe CD DIRECT button is selected, the audio and
video
recording
output
is automatically
prohi-
bited, so it is advisable to use the REC SELECT
button @ to prevent accidentally interrupting the
recording.
CD DIRECT button
This button is used to enjoy the audio signals input
from the component
connected to the CD jacks on
the rear panel with higher sound quality. In the CD
direct mode, the audio signals bypass such circuitry
as the surround and tone control circuits, and are
output directly to the front speakers for higher sound
quality.
* Cancelling the CD direct mode
When in the CD direct mode, either press the CD
DIRECT button once again, or press the AUDIO
FUNCTION
selector button @ or VIDEO FUNC-
TION selector button @ or BYPASS button @ or
SURROUND
MODE
selector button @ to cancel
the CD direct mode.
NOTE:
e When the CD DIRECT button © is selected, the
output of signals to the audio and video output
jacks
is automatically
prohibited,
so
the
REC
SELECT (independent audio/video recording) and
VIDEO SELECT (independent video signal selec-
tor) buttons do not work. Also, if the REC SELECT
button is selected or when using the tape monitor
button, the CD DIRECT button will not function.
@
STANDBY LED
This LED remains lit when the set is in the normal
operating mode or in the standby mode, and flashes
when
in the muting
mode.
REMOTE
SENSOR
This is where the signals from the wireless remote
control unit are received.
Point the remote contro! unit at this sensor when
operating it.
MFD
(multi-function fluorescent display)
Information
such as the surround
mode
and the
input and output are displayed here when the power
is turned on.
Normally the surround mode is displayed. If another
button is pressed, a display pertaining to that button
is shown
for approximately
5 seconds
(this time
differs according to the display), after which the
surround
mode
is once again displayed.
Refer to pages
9 to 10 for details on the MFD
displays.
AUDIO FUNCTION
selector button
This button is used to switch the audio input. Press
this button repeatedly or hold it in to change the
input in the following order:
ne
PHONO ——-——~ CD ———>
TUNER eas
(All the video outputs are off unless a video function
is selected with the VIDEO SELECT button or the REC
SELECT
button.)
VIDEO FUNCTION
selector button
This button is used to switch the video input. Press
this button repeatedly or hold it in to change the
input in the following order:
VDP/DBS ——-————> VCR--1
Set (ee
ees
MASTER
VOLUME
control
Turn the control clockwise
( ™)
to increase the
volume, counterclockwise
( © ) to decrease
it.
PHONES
jack
This jack is for connecting
headphones.
To cut the sound from the speakers, either turn off
the output (speakers) from the remote control unit or
turn off the output of the component connected to
the PRE OUT jacks.
BYPASS
(surround bypass) button
When this button is pressed, the surround mode is
bypassed and the normal stereo sound is produced.
No signals are output to the rear channel.
lf the SURROUND
MODE button is pressed when in
the bypass mode, the mode
returns to the mode
which was set before the bypass mode was turned
on.
*
In the initial setting the center output is turned off.
SURROUND
MODE
selector button
Use this button to select the surround
mode.
Either press it repeatedly or hold it in to change the
surround
mode
in the order shown
below.
For details, refer to pages
15 to 16.
DOLBY PRO LOGIC
{
WIDE SCREEN
|
LIVE
4
MONO
MOVIE
J
CLASSIC CONCERT
}
ROCK CONCERT
,
CHURCH
|
JAZZ
4
STADIUM
4
MATRIX
=
Continued
®
0 CENTER
MODE
selector button
This button is used to select the center mode when
in the Dolby Pro Logic, WIDE
SCREEN
or LIVE
modes. Select the mode according to the speaker
system
you are using.
p7® NORMAL
—*+@ PHANTOM —*@) WIDE 7
The mode switches as follows in the Dolby 3CH
Logic mode:
@ NORMAL <
@ WIDE
*
If this button is pressed in a mode other Dolby Pro
Logic, live and wide screen, the Dolby Pro Logic
mode
is set automatically.
For details, refer to page
16.
3CH LOGIC
(three-channel logic) button
This button only functions when in the Dolby Pro
Logic mode. When pressed again, the three-channel
logic mode turns off and the normal Pro Logic mode
is set.
The 3CH LOGIC key does not function when in the
Dolby Pro Logic Phantom
mode.
For details, refer to page 16.
HI-VISION
((Hi-Vision input switch for use with BS (broadcast
satellite) broadcasts))
This function
is to be used with future satellite
broadcasts. The signals connected to the CENTER
and REAR of the HI-VISION jacks on the rear panel do
not
pass
through
the surround
circuits,
but are
output directly to the center and rear speakers.
NOTE:
The
mode
automatically
switches
to the bypass
mode when using the tape monitor function in the
Hi-Vision
mode.
VIDEO SELECT
{independent video signa! selector) button
This
button
is used
to select
the
video
signal
independently
of the audio signal. When
pressed
once, the video selector function turns on. When the
button is held in, the video input signal changes in
the order shown below. Release the button when the
desired video input signal is displayed on the MFD.
After this is done, the video signal will not change
even if the AUDIO FUNCTION selector button @ is
pressed and the audio input is changed.
To cancel the independent
video signal selection
mode, either press the VIDEO SELECT button again,
or press the VIDEO FUNCTION
selector button @.
VDP/DBS —————_- VCR-1
ay
tp eon
ee
Werbung
