Warranty; Accessories; Technical Data - Kärcher IB 10/8 L2P Originalbetriebsanleitung

Fault
The pellet production fault in-
dicator lights up
The pellet metering fault indi-
cator lights up
The pellet metering fault indi-
cator flashes
The voltage supply indicator
light does not light up
The compressed air indicator
light does not light up
The device does not work
Poor cleaning performance
Pellet dosage too low
Recurring interruptions in the
dry ice stream
Performing a reset
1. Press the reset button inside the device
with a screwdriver.
Illustration O
Replacing the carbon dioxide filter
ATTENTION
Malfunctions
Contaminated carbon dioxide can cause
malfunctions.
When working on the carbon dioxide filter,
be careful not to get any dirt into the device.
ATTENTION
Malfunctions
Malfunctions due to contamination.
After each loosening or unscrewing of the
screw plug, the carbon dioxide filter and the
copper seal must be replaced. If this is not
done, particles can become detached from
the carbon dioxide filter and lead to mal-
functions.
Note
The carbon dioxide filter is backwashed
and cleaned as soon as the pressurised
cylinder connection is disconnected from
the carbon dioxide cylinder. Regular re-
placement of the carbon dioxide filter is
therefore not necessary.
1. Close the stop valve on the carbon diox-
ide bottle.
2. Operate the unit at the highest level for
about 1 minute to depressurise the car-
bon dioxide hose.
3. Unscrew the screw flange on the carbon
dioxide bottle.
4. Carefully unscrew the screw plug from
the screw flange. Let the hose flange
Rectification
 Allow the device to thaw out. Check the carbon dioxide filter and change it if necessary. Then per-
form a reset.
 If the malfunction occurs repeatedly, replace the carbon dioxide bottle.
 Switch the device off and back on again.
 If the fault indicator remains lit, contact the customer service.
 Allow the metering motor to cool down. Position the device so that air can flow into the device from
below. Contact Customer Service if necessary.
 Plug the mains plug into the socket.
 Check the on-site voltage supply.
 Connect a compressed air hose to the device.
 Open the stop valve in the on-site compressed air supply.
 Check the indicator lights and fault indicators.
 Perform a reset.
 Turn the program switch to a higher level.
 Increase the jet pressure.
 Check the filling level of the carbon dioxide bottle.
 Do not use a heated carbon dioxide bottle. Protect the carbon dioxide bottle from heat radiation.
The effectiveness of the pellet production drops sharply if the temperature of the carbon dioxide is
above 31 °C.
 Allow the abrasive hose and the jet gun to thaw to clear any blockages. Then increase the jet pres-
sure.
 Turn the program switch to a higher level.
 Replace the carbon dioxide filter between the carbon dioxide bottle and the device.
 Turn the programme switch to a lower level or increase the jet pressure.
 If the jet nozzle is clogged:
a Immediately close the carbon dioxide bottle.
b Allow the unit to thaw for 30 minutes.
c Increase the jet pressure.
d Start the appliance with the carbon dioxide bottle closed to remove pellet residues.
hang down to prevent dirt from entering
the carbon dioxide hose.
Illustration P
Screw flange
1
Carbon dioxide filter
2
Copper sealing ring
3
Screw plug
4
5. Remove the carbon dioxide filter.
6. Vacuum out the screw plug and the
screw flange.
7. Carefully press the new carbon dioxide
filter onto the screw plug by hand.
8. Replace the copper seal.
9. Tighten the screw plug, holding the wide
hexagon of the screw flange with an
open-end wrench.
Tightening torque: 80 Nm.
The warranty conditions issued by our rele-
vant sales company apply in all countries.
We shall remedy possible malfunctions on
your appliance within the warranty period
free of cost, provided that a material or
manufacturing defect is the cause. In a war-
ranty case, please contact your dealer (with
the purchase receipt) or the next author-
ised customer service site.
(See overleaf for the address)

Accessories

ABS residual pressure valve
Order number 2.574-006.0
Necessary when using carbon dioxide bot-
tles with a residual pressure valve.

Warranty

English

Technical data

Electrical connection
Mains voltage
Phase
Frequency
Power rating
Degree of protection
Leakage current, typical
Residual current device
Compressed air connection
Compressed air hose,
nominal width (min.)
Pressure (max.)
Compressed air consump-
tion, max.
Device performance data
Jet pressure, max.
Jet pressure, min. level 1
Jet pressure, min. level 2
Jet pressure, min. level 3
Carbon dioxide consump-
tion
IB 10/
8 L2P
V 220...
230
~ 1
Hz 50...6
0
kW 1,0
IPX4
mA <3,5
delta I, 0,03
A
Inches 0,5
MPa 1,0
(bar) (10)
3
m / 0,8
min
MPa 1,0
(bar) (10)
MPa 0,07
(bar) (0,7)
MPa 0,14
(bar) (1,4)
MPa 0,28
(bar) (2,8)
kg/h 20...6
0
17