Operation; Transport; Storage; Care And Maintenance - Kärcher PW 30/1 Originalbetriebsanleitung

Using the additional socket
1. Open the protective cover of the additional socket.
2. Plug the unit plug of the PW 30/1 into the additional
socket of the Puzzi washing vacuum.
3. Put PW 30/1 into operation.

Operation

Switching on the device
1. Put the Puzzi washing vacuum into operation.
2. Start the brush drive on the power switch of the PW
30/1.
Illustration E
Note
When the brush is blocked, the brush drive switches off.
For remedy see troubleshooting guide.
Cleaning
1. Operate the valve handle. This is used to spray on
the detergent solution. The waste water is immedi-
ately vacuumed back in via the suction nozzle.
Illustration F
2. For cleaning, pull PW 30/1 backwards over the car-
pet in slightly overlapping paths. Start in such a way
that areas that have already been cleaned do not
have to be walked on again.
3. Release the valve handle when moving forward (idle
stroke).
Switching off the device
1. Switch off the brush drive at the power switch.
2. Set the Puzzi washing vacuum out of operation.

Transport

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Pull the device behind you with the suction pipe
when transporting it over longer distances.
2. Carry the device by the casing and suction pipe.
3. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.

Storage

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.

Care and maintenance

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Unplug the unit.
Maintenance intervals
Each time after use
1. Rinse PW 30/1 with clear water.
2. Clean the roller brush of lint and dirt.
3. Check the spray pattern of the nozzle mouthpiece; if
the spray pattern is uneven, clean the nozzle and
mouthpiece.
8
4. Clean the suction hose and suction nozzles when
the suction performance decreases.
1. Check toothed belt wear and tension, replace
toothed belt if necessary.
2. Check brush wear, replace brush if necessary.
Maintenance work
Replacing the roller brush
1. Release 5 screws and remove the cover.
2. Remove the toothed belt.
3. Unscrew the screw on the front of the brush.
4. Dismantle the retaining plate on the opposite side by
loosening 3 screws and remove the brush.
5. Installation of the brush is performed in the reverse
sequence.

Troubleshooting guide

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Unplug the unit.
Brush is blocked
Note
When the brush is blocked, the brush motor is switched
off.
1. Check brush for dirt and remove any blocking ob-
jects if necessary.
2. Unscrew the protective cover and press the fuse
switch using a screwdriver. Screw the protective
cover back in.
Customer Service department
If the malfunction cannot be corrected, the device must
be checked by the Customer Service department.
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Accessories and spare parts

Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Spray extraction device
Type: 1.913-xxx
English
Half-yearly

Warranty