Technical Data - Scheppach HS110 Serie Original Bedienungsanleitung

11. Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12. Only use the supplied saw blade for cutting wood,
never for the processing of metals.
13. Use the correct saw blade for the material to be
processed.
14. Use only a saw blade with a diameter that matches
the specifications on the saw.
15. Use only saw blades that are marked with an equal
or higher rotational speed than that marked on the
power tool.
16. Use only saw blades recommended by the manu-
facturer which conform to EN 847-1, if intended for
cutting wood or similar materials.
17. Wear suitable personal protective equipment,
such as:
-Hearing protection;
-Protective gloves when handling saw blades.
18. Only use saw blades recommended by the man-
ufacturer which conform to EN 847-1. Warning!
When changing the saw blade, ensure that the
cutting width is not smaller and the width of the
saw blade disc is not greater than the thickness of
the riving knife!
19. When sawing wood and plastics, avoid the saw
teeth overheating. Reduce the feed speed in order
to avoid the plastic melting.
20. Please note that complex non-through cutting op-
erations and tapered cuts are not permitted.
21. Avoid bevel ripping on bevelling side of the saw
blade.
Residual risks
The electric tool has been built according to state-
of-the-art and the recognised technical safety
rules. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the "Safety in-
structions" and the "Proper use" are observed along
with the whole of the operating instructions.
• Do not unnecessary stress the machine: too much
pressure when sawing will damage the saw blade
quickly. This results in reduced output of the ma-
chine in the processing and in cut precision.
36 | GB
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Keep your hands away from the work area, when the
machine is in operation.
• Before maintaining or adjusting, switch off the ma-
chine and unplug the power plug.
m WARNING
This power tool generates an electromagnetic field dur-
ing operation. This field can impair active or passive
medical implants under certain conditions. In order to
prevent the risk of serious or deadly injuries, we recom-
mend that persons with medical implants consult with
their physician and the manufacturer of the medical im-
plant prior to operating the power tool.
7.

Technical data

AC motor
Power
Operating mode
Idle speed
Carbide saw blade
Number of teeth
Riving knife thickness
Min. workpiece
dimensions W x L x H
Table size
Cutting height max. 90°
Cutting height max. 45°
Height adjustment
Tilting saw blade
Extraction connection
Weight approx.
* Operating mode S6 40%: Continuous duty with inter-
mittent loading (operating time 10 mins). To avoid im-
permissible overheating of the motor, the motor should
be driven for only 40% of the operating time with the
stipulated nominal power and must then continue to
run with no load for the remaining 60% of the operating
time.
www.scheppach.com
230 - 240V ~ 50Hz
1800 Watts
S6 40% 2000 Watts*
5000 rpm
ø 254 x ø 30 x 2.8 mm
24
2.5 mm
10 x 50 x 1 mm
850 x 580 mm
85 mm
65 mm
0 - 85 mm
0 - 45°
ø 40 mm
21,5 kg