Operation; Working Notes - Scheppach HS110 Serie Original Bedienungsanleitung

3. Turn the transverse stop (31) until the desired an-
gle has been set. The notch on the guide rod indi-
cates the set angle.
4. Retighten the knurled screw (29).
5. To extend the transverse stop (31) with the stop
rail (30), the stop rail (30) must be removed from
the parallel stop (14). Now mount the stop rail as
shown in Fig. 20 using the knurled nuts (i).
ATTENTION: Do not slide the stop rail (30) too far in
the direction of the saw blade. The distance between
the stop rail (30) and the saw blade (4) must be approx.
2 cm.
10.6 Setting the scale of the parallel stop (Fig. 21)
Check whether the indicator on the sight glass (32) of
the parallel stop (14) shows correct values in relation
to the cutting line. If this is not the case, proceed as
follows:
1. Loosen the screw (32a) which fixes the indicator
to the sight glass (32) of the parallel stop (14). Now
the indicator on the sight glass (32) can be set to
the correct position.
2. Now retighten the screw (32a) on the sight glass
(32).

11. Operation

11.1 Working notes

• After every new setting, we recommend performing
a test cut, in order to check the dimensional settings.
• Wait after the saw has been switched on, until the
saw blade has reached full speed, before starting
the cutting process.
• Secure larger workpieces against tipping after the
cutting process (for example a reel-off stand etc.)
• Be careful when cutting.
• Only operate the device with an extraction system.
• Check and clean the extraction channels at regular
intervals.
11.2 Suitability of the saw blades
• 24 teeth: soft materials, high degree of chip take-off,
coarse cutting pattern
• 48 teeth (not included in the scope of delivery): hard
materials, lower degree of chip take-off, finer cutting
pattern
40 | GB
11.3 Carrying out longitudinal cuts (Fig. 22)
Here, a workpiece is cut in its longitudinal direction.
One edge of the workpiece is pressed against the par-
allel stop (14) while the flat side lies on the saw table
(1).
The saw blade guard (2) must always be lowered onto
the workpiece. The working position for the longitudinal
cut must never be in line with the cutting process.
1. Adjust the parallel stop (14) and stop rail (30) to suit
the height of the workpiece and the desired width.
2. Switch on the saw.
3. Place your hands flat on the workpiece with your
fingers closed and slide the workpiece along the
stop rail (30) into the saw blade (4).
4. Guide laterally with the left or right hand (depend-
ing on the position of the parallel stop) only up to
the front edge of the saw blade guard (2).
5. Always push the workpiece through to the end of
the riving knife (3).
6. The cutting waste remains on the saw table (1) un-
til the saw blade (4) is in the resting position again.
7. Secure long workpieces against tipping at the end
of the cutting process! (e.g. roller stand, etc.)
ATTENTION: The parallel stop must be set parallel
with the saw blade. Check the alignment and tight fit of
the parallel stop (14), especially during use and when
not in use for a longer period of time.
Vibrations can cause screw connections to loosen. If
necessary, readjust the parallel stop (14) and retighten
the knurled nut (i). Fix the screw connections (k) with
the Allen key (not included in the scope of delivery)
(Fig. 19a).
11.3.1 Cutting narrow workpieces (Fig. 23)
Longitudinal cuts of workpieces with a width of less
than 120 mm must always be made with the aid of a
push stick (17). The push stick (17) is included in the
scope of delivery. Replace a worn or damaged push
stick (17) immediately.
1. Set the parallel stop (14) to suit the intended work-
piece width.
2. Push the workpiece forward with both hands, and
be sure to use a push stick (17) as a pushing aid in
the area of the saw blade.
3. Always push the workpiece through to the end of
the riving knife (3).
m ATTENTION: For short workpieces, use the push
stick as soon as you start cutting.
www.scheppach.com