Operation - Scheppach HS110 Serie Original Bedienungsanleitung

9.1 Assembling the frame and table width extension
(Fig. 4-10)
1. Turn circular table saw upside down and place on
the floor.
2. Fasten the table width extension (6) loosely onto
the saw table (1) with the hexagonal bolts (a), the
washers (c), the spring washers (d) and the nuts
(e) (Fig. 6).
3. The four legs (19) are screwed to the housing to-
gether with the table supports (24) (Fig. 7).
4. Fasten the table supports (24) loosely to the table
width extensions (6) with the hexagonal bolts (a),
the washers (c), the spring washers (d) and the
nuts (e). Loosely tighten the legs (19) and the table
supports (24) onto the housing of the circular table
saw with the hexagonal bolts (a).
5. Now screw the four centre struts (20a, 20b) loose-
ly onto the legs (19). Use the coach bolts (b), the
washers (c), the spring washers (d) and the nuts
(e) (Fig. 8).
6. Screw on the stands (22) at the holes in the rear
legs (19). Assembly materials: 2 coach bolts (b),
the washers (c), spring washers (d) and nuts (e)
respectively (Fig. 9).
ATTENTION: Both stands must be fastened to the
fastening points (23) on the rear of the machine
(Fig. 9).
7. Align the table width extension (6) level with the
saw table (1).
8. Now tighten all screws for the legs (19) and the
table width extension (6).
9. Now plug the rubber feet (21) onto the legs (19)
(Fig. 10).
10. Place the circular table saw on the machine stand
(11).
9.2 Fitting/removing the saw blade guard
(Fig. 11+12)
1. Loosen the screw with nut and washer (27) of the
saw blade guard (2). Place the saw blade guard (2)
onto the riving knife (3) from above.
2. Fit the screw with nut and washer (27) such that
the screw (27) sits firmly in the elongated hole.
3. Do not over-tighten the screw (27). The saw blade
guard (2) must remain free to move.
4. Disassembly takes place in reverse order.
m WARNING: Before starting sawing, the saw blade
guard (2) must be lowered onto the material to be sawn.
38 | GB
After fitting, check that the saw blade guard (2) is func-
tioning properly. Lift the saw blade guard and then
release it. The saw blade guard should automatically
move back to its starting position.
9.3 Fitting/adjusting the riving knife (Fig. 11-14)
Attention! Pull out the mains plug! The setting of
the saw blade (4) must be checked after every saw
blade replacement.
1. Set the saw blade (4) to the max. cutting depth,
move to the 0° position and lock in place.
2. Remove the saw blade guard (2) (not with first in-
stallation).
3. Loosen the two countersunk head screws of the
table inlay (25) and pull out the table inlay (5).
4. Loosen the fixing screw of the riving knife (26) (use
the 10 mm open-ended spanner supplied for this
purpose).
5. Slide the riving knife (3) upwards.
6. The distance between the saw blade (4) and the
riving knife (3) should be 3-5 mm. (fig. 1, 3)
7. Tighten the fixing screw (26) again and fit the table
inlay (5).
8. Mount the saw blade guard (2) with the screw and
knurled nut and flat washer (27).
When dismantling the riving knife, please proceed in
reverse order to that described in 9.3.
9.4 Connecting an extraction device (Fig. 2)
1. Connect a suction hose to the suction adapter (16).
Secure the suction hose with a hose clamp (not
included in the scope of delivery) if necessary, to
prevent it slipping off the suction adapter (16).
2. A household vacuum cleaner is not suitable for
use as an extraction device. Use a multi-purpose
suction device or an extraction system designed
specifically for sawdust.

10. Operation

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
10.1 ON/OFF switch (Fig. 3)
• It is possible to switch the saw on by pressing the
green "I" button. Before starting sawing, wait until
the saw blade has reached its maximum speed.
www.scheppach.com