Technical Data; Attachment And Operation - Scheppach 3901302920 Originalbetriebsanleitung

along with the whole of the operating instructions.
• Do not unnecessary stress the machine: too
much pressure when sawing will damage the saw
blade quickly. This results in reduced output of the
machine in the processing and in cut precision.
• Avoid accidental starting of the machine: the
operating button may not be pressed when inserting
the plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Keep your hands away from the working area when
the machine is in operation.
• Before performing setting or maintenance work,
switch the device off and unplug the mains plug.

6. Technical data

AC motor 230 V~ 50 Hz 400 V~ 50 Hz
Power 2200 W
Operating mode S6 40% *
Idle speed 2800 min
Connector Schuko
Carbide saw blade 24 Z
pre-mounted
Table size
Table height
Cutting height max. 90°
Cutting height max. 45°
Height adjustment
Tilting saw blade
Cutting speed
Weight approx.
* Operating mode S6 40%: Continuous duty with
intermittent loading (operating time 10 mins). To
avoid impermissible overheating of the motor, the
motor should be driven for only 40% of the operating
time with the stipulated nominal power and must then
continue to run with no load for the remaining 60% of
the operating time.
Noise level
The noise levels have been determined in accordance
with EN 1870.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing.
Total vibration emission values (vector sum of three
directions) determined per EN 1870.
26 | GB
2800 W
S 6/40 %
2760 min
-1 -1
CEE 16 A
ø 315 x ø 30 x 3 mm
800 x 550 (950) mm
800 mm
83 mm
49 mm
0 - 83 mm
0 - 45°
46 m/sec
44 kg
102,5 dB(A)
3 dB
112,4 dB(A)
3 dB
www.scheppach.com

7. Attachment and operation

Before commissioning
• Prior to commissioning, all covers and safety
devices must be mounted correctly.
• The saw blade must be able to run freely.
• In case of previously machined wood, be aware of
any foreign bodies, such as nails or screws, etc.
• Before pressing the on/off switch, make sure that
the saw blade is correctly fitted, and that moving
parts run smoothly.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Only connect the machine to a correctly installed
protective contact socket, with fuse protection of at
least 16A.
Attention! Remove the mains plug before any
maintenance, modification and assembly work on the
circular saw.
Place all supplied parts on a flat surface. Group equal
parts.
Note: If connections are secured with a screw (round
head/or hexagon), hexagonal nuts and washer, the
washer must be placed under the nut.
Insert screws each from outside to inside. Secure
connections with nuts on the inside.
Note: During assembly, tighten the nuts and bolts
only to the extent that they cannot fall off.
If you tighten the nuts and screws fully before final
assembly, it is not possible to complete the assembly.
Fig. 1
Place the tabletop (1) on a workbench (remove
packing pad a under the motor).
Fig. 1.1
Mount the frame leg (2) to the tabletop with 2 M6 x 16
hexagonal bolts, 2 washers 6 and 2 M6 nuts.
Fig. 2
Mount the switch (6) to the tabletop with 2 M6 x 16
hexagonal bolts, 2 washers 6 and 2 M6 nuts.
Fig. 3
Mount the frame leg (3) to the tabletop with 2 M6 x 16
hexagonal bolts, 2 washers 6 and 2 M6 nuts. Tighten
the bolts lightly by hand.
Fig. 4
Mount the frame leg (4) to the tabletop with 2 M6 x 16
hexagonal bolts, 2 washers 6 and 2 M6 nuts. Tighten
the bolts lightly by hand.