Scheppach HS110 Serie Original Bedienungsanleitung Seite 39

• In order to switch the saw off again, it is necessary to
press the red "0" button.
10.2 Setting the cutting depth (Fig. 1+3)
The saw blade (4) can be adjusted to the required cut-
ting depth by turning the hand wheel (9).
• Counterclockwise: Greater cutting depth
• Clockwise: Smaller cutting depth
Check the setting with a test cut.
10.3 Setting the angle (Fig. 1, 15, 19, 20)
Angled cuts of 0°-45° to the left of the parallel stop (14)
can be carried out with the circular table saw.
m Before making every cut, check that no collision can
occur between the stop rail (30), transverse stop (31)
and the saw blade (4).
1. Loosen the locking handle (7).
2. Set the desired angle on the scale by turning the
hand wheel (9).
3. Lock the locking handle (7) at the desired angle
setting.
10.4 Using the parallel stop (Fig. 15-21)
10.4.1 Setting the stop height (Fig. 15+16)
• The stop rail (30) of the parallel stop (14) has two
guide surfaces at different heights.
• Depending on the thickness of the material to be
cut, the stop rail (30) must be used for thick materi-
al (workpiece thickness exceeding 25 mm) and thin
material (workpiece thickness below 25 mm).
10.4.2 Turning the stop rail (Fig. 15)
1. To turn the stop rail (30), first loosen the knurled
nuts (i).
2. The stop rail (30) can now be pulled off the parallel
stop (14) and then slid over this again with the cor-
responding guide.
3. Tighten the knurled nuts (i) again.
4. The stop rail (30) can be attached to the left or right
of the parallel stop (14) as required. To do this, only
mount the screws from the other side of the paral-
lel stop (14).
10.4.3 Setting the cutting width (Fig. 16+17)
The parallel stop (14) must be used when cutting sec-
tions of wood lengthways.
1. Place the parallel stop (14) from above on the
guide rail (15) for the parallel stop (14).
2. 2 scales are printed on the guide rail (15) for the
parallel stop (14), which show the distance be-
tween the parallel stop (14) and the saw blade (4).
3. Select the appropriate scale depending on wheth-
er the stop rail (30) has been turned for processing
thicker or thinner material:
High stop rail: thick material
Low stop rail: thin material
4. Set the parallel stop (14) to the desired dimension
on the sight glass and use the eccentric lever (13)
for the parallel stop (14) to fix in place.
10.4.4 Setting the stop length (Fig. 18)
In order to avoid the material to be cut becoming
jammed, the stop rail (30) can slide in a longitudinal
direction.
Rule of thumb: The rear end of the stop abuts an imag-
inary line. This starts approximately at the centre of the
saw blade and runs backwards at 45°.
1. Set the required cutting width.
2. Loosen the knurled nuts (i) and slide the stop rail
(30) far enough forward that it touches the imagi-
nary 45° line.
3. Tighten the knurled nuts (i) again.
10.4.5 Calibrating the parallel stop (Fig. 19+19a)
ATTENTION: Remove the saw blade guard (2)
(see 9.2).
1. Set the saw blade (4) to the maximum cutting
depth.
2. Set the parallel stop (14) such that the stop rail (30)
makes contact with the saw blade (setting for thick
material, see 10.4.3).
Make sure when mounting or when installing the paral-
lel stop that it must be aligned parallel to the saw blade.
If the parallel stop (14) is not in line with the saw blade
(4), proceed as follows:
1. Loosen the screws (k) on the parallel stop suffi-
ciently that the parallel stop (14) can be aligned
parallel to the saw blade (4).
2. Tighten the screws (k) again.
10.5 Using the transverse stop (Fig. 20)
When trimming, the transverse stop (31) must be ex-
tended with the stop rail (30).
1. Slide the transverse stop (31) in the groove (28a)
of the saw table.
2. Loosen the knurled screw (29).
www.scheppach.com GB | 39