Technical Data - Roller's Multi-Press 22 V ACC Connected Betriebsanleitung

eng
Safety Notes for
ROLLER'S Multi-Press 22 V ACC Connected
WARNING WARNING
Read all the safety notes, instructions, illustrations and technical data which
come with this power tool. Failure to heed the following instructions can lead to
electric shock, fi re and/or severe injuries.
Keep all safety notes and instructions for the future.
● Do not use the power tool if it is damaged. There is a danger of accident.
● Hold the power tool fi rmly by the housing grip (6) and pistol grip (8) and
make sure you are standing fi rmly when working. The power tool produces a
very high pressing force. It is safer to hold the tool with both hands. Therefore be
very careful. Keep children and bystanders away while operating the power tool.
● Do not reach into moving parts in the pressing area. There is a risk of injury
by crushing fi ngers or hands.
● Never operate radial presses with the tong retaining bolt unlocked (2). There
is a risk of fracture and fl ying parts can cause serious injuries.
● Always position the radial press with pressing tongs or with pressing ring
and adapter tongs on the press fi tting at a right angle to the pipe axis. If
the drive unit is positioned askew to the pipe axis, its high drive force will pull it
to a right angle to the pipe axis. This could crush hands or other parts of the body
and/or there is a risk of fracture whereby fl ying parts can cause serious injuries.
● Always position the S (PR-2B) pressing ring on the press fi tting at a right
angle to the pipe axis. When positioning the radial press with Z8 adapter
tongs on the S pressing ring, make sure that the radial press can swivel
freely. There is a risk of fracture whereby fl ying parts can cause serious injuries.
● Do not start the radial press without pressing tongs or pressing ring with
pressing tongs. Do not start the pressing process except to make a press joint.
The drive unit, pressing tongs, pressing ring and adapter tongs will be exposed
to unnecessarily high loads without counter-pressure by the press fi tting.
● Before using pressing tongs, pressing rings with adapter tongs (pressing
jaws, pressing slings with adapter jaws) from other manufacturers, check
whether these are suitable for the ROLLER'S radial presses. Pressing tongs
and pressing rings with adapter tongs from other manufacturers can be used in
the ROLLER'S Multi-Press 22 V ACC Connected if they are designed for the
required 32 kN thrust force, fi t mechanically into ROLLER'S drive units, can be
locked properly and fracture safely, e.g. without the risk of parts fl ying off the
pressing jaws, at the end of their life or when overloaded. It is recommended to
only use pressing tongs and pressing rings with adapter tongs which are designed
with a safety factor ≥ 1.4 against permanent fracture, i.e. withstand a necessary
thrust force of 32 kN up to a thrust force of 45 kN. Also read and observe the
instruction manuals and safety instructions of the respective manufacturer/supplier
of the pressing tongs, pressing rings with adapter tongs and the installation and
assembly instructions of the manufacturer/supplier of the press fi tting system to
be pressed and observe any restrictions for use that are specifi ed there. Failure
to do so could lead to fracture and fl ying parts can cause serious injuries.
● Use only undamaged pressing tongs, pressing rings and adapter tongs.
Damaged pressing tongs, pressing rings and adapter tongs can jam or fracture
and lead to a faulty press fi tting. Damaged pressing tongs, pressing rings and
adapter tongs must not be repaired. Failure to do so could lead to fracture and
fl ying parts can cause serious injuries.
● Do not use the carrying ring (26) as fall protection. The carrying ring is solely
for hooking in shoulder straps. Have the drive unit checked over by an authorised
ROLLER customer service workshop if the carrying ring has been subjected to
heavy strain.
● Pull out the mains plug or remove the battery before assembling/dismantling
pressing tongs, pressing rings and adapter tongs. There is a risk of injury.
● Comply with the maintenance regulations for the power tool and follow the
maintenance instructions for pressing tongs, pressing rings and adapter
tongs. Following the maintenance instructions has a positive effect on the life of
the power tool, the pressing tongs, pressing rings and adapter tongs.
● Never let the power tool operate unattended. Switch off the power tool
during longer work breaks, pull out the mains plug/battery. Electrical devices
can cause hazards which lead to material damage and/or injury when left unat-
tended.
● Place maximum 3 XL 64–108 (PR-3S) pressing rings in the XL-Boxx system
case with inlay for XL 64–108 (PR-3S) pressing rings (accessory art. no.
579603). Compliance with the maximum load capacity of 3 XL (PR-3S) pressing
rings reduces the risk of material damage and/or injury.
● Check the power cable and extension leads of the power tool and the power
supply unit regularly for damage. Have these renewed by qualifi ed experts or
an authorised ROLLER customer service workshop in case of damage.
● Only allow trained persons to use the power tool. Apprentices may only use
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
● Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the power tool
safely may not use this power tool without supervision or instruction by a
responsible person. Otherwise there is a risk of injury from incorrect operation.
● Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
20
DANGER DANGER
● Observe and follow the safety notes and instructions for the ROLLER'S
pressing tongs, ROLLER'S pressing rings, ROLLER'S adapter tongs,
ROLLER'S M cropping tongs, ROLLER'S cable shears, ROLLER'S Basic
E01 pressing tongs, and ROLLER'S pressing inserts. Failure to observe the
safety notes can result in material damage, injury, electric shock or a fall.
See also www.albert-roller.de → Downloads → Safety Notes: RADIAL PRESSES
Safety Notes for Batteries, Rapid Chargers,
Power Supply Units
WARNING WARNING
Read all the safety notes, instructions, illustrations and technical data which
come with this power tool. Failure to heed the instructions can result in electric
shock, fi re and/or severe injuries.
Keep all safety notes and instructions for the future.
See also www.albert-roller.de → Downloads → Instruction Manuals → Safety Notes
→ Safety Notes Batteries, Rapid Chargers, Power Supply Units.
Safety Data Sheets
WARNING WARNING
Read the safety data sheets. Failure to heed the instructions can result in electric
shock, fi re and/or severe injuries.
Keep all safety notes and instructions for the future.
See www.albert-roller.de → Downloads → Safety Data Sheets → Batteries.
Explanation of Symbols
DANGER DANGER
Danger with a high degree of risk which results in death or
severe injury (irreversible) if not heeded.
WARNING WARNING Danger with a moderate degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety instruction! No risk of injury.
Danger
Falling
Electrical voltage
Read the instruction manual before use
Use eye protection
Use ear protection
Power tool corresponds to protection class II
Not suitable for using outdoors
Switched-mode power supply (SMPS)
Short-circuit-proof safety transformer (SCPST)
Environmental friendly disposal
CE conformity mark

1. Technical Data

Use for the Intended Purpose
WARNING WARNING
ROLLER'S Multi-Press 22 V ACC Connected is intended for making press fi ttings
of all common press fi tting systems, for making connections for electric cables, for
making connections for fall protection systems, for cutting threaded bars and for
cutting electric cables. The drive unit can be connected via Wi-Fi to the Internet to
exchange data between the drive unit and the Cloud. All other uses are not for the
intended purpose and are therefore prohibited.
eng