Inhaltsverzeichnis
Werbung
GB
PRÆCISIONSCIRKELSAV FES-350
D
Numrene i den nedenstående tekst henviser til illustrationerne på side 2 - 5.
For din egen og andres sikkerhed anbefaler vi at du læser denne brugsanvisning
NL
nøje igennem, før maskinen tages i brug. Opbevar denne brugsanvisning og den
øvrige dokumentation ved maskinen.
F
IIndledning
Denne maskine er beregnet til privat brug og til at save i forskellige slags tynde materialer.
Præcisionscirkelsaven kan bruges, hvis der skal saves præcist og støvfrit eller hvis der er risiko
E
for at ramme rør eller kabler. Præcisionscirkelsaven er unik, fordi det materiale, der skal saves
med maskinen bliver klemt fast mellem basispladen og arbejdsbænken. Derefter bliver
P
savklingen trykket ned i det materiale, der skal saves, hvorved man får et hurtigt, nemt og pænt
resultat.
I
Indhold
1.
Maskindata
2.
Sikkerhedsinstruktioner
S
3.
Anvendelse
4.
Service og vedligeholdelse
FIN
1. MASKINDATA
Tekniske specifikationer
N
Spænding
DK
Effekt
Savdybde
Omdrejningstal, uden belastning
Maks. driftscyklus
Reduktion
Savklinge diameter
Vægt
Maks. klingediameter
Maks./min. klingebredde
Rystefrekvens
Lydtrykniveau
Lydtrykniveau-ækvivalent
114
| 230 V~50 Hz
| 350 W
| 0-12 mm
| 4000 omdr. pr. minut
| 3 min/5 min
| 8.4:1
| 50,8 mm
| 1,2 kg
| 50,8 mm
| 2 mm/ 0,75 mm
| < 2,5 m/s
2
| 86,1 dB(A)
| 99,1 dB(A)
Ferm
Lubrication
If it is difficult to rotate the adjustment knob, unscrew it until the rubber seal becomes visible.
Use a soft brush to clean the area around the seal and apply a few drops of synthetic oil to it.
Faults
Contact the maintenance address stated on the warranty card if the saw becomes faulty, for
example, in the case of wear of one of the parts. An exploded view included at the back of this
instruction manual lists the parts you can order.
Environment
In order to avoid damage during transport, the saw is delivered in strong packaging material.
Where possible, recyclable packaging material has been used. Therefore, please recycle the
packaging material.
Faulty and/or discarded electrical or electronic tools should be handed over to a
recognized collection point for disposal.
Warranty
See the warranty card in the back of this instruction manual for the warranty terms.
CE
DECLARATION OF CONFORMITY
We declare under our sole responsibility that
is in conformity with the following standards or standardized documents:
EN60745-1, EN60745-2-5, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3
in accordance with the regulations.
98/37/EC, 2006/95/EC, 89/336/EEC, 2002/95/EC, 2002/96/EC
from 01-08-2007
ZWOLLE NL
J.A. Bakker - van Ingen
CEO Ferm BV
It is our policy to continuously improve our products and we therefore reserve the right to
change the product specification without prior notice.
Ferm BV • Lingenstraat 6 • 8028 PM Zwolle • The Netherlands
Ferm
(GB)
FES-350
J. Lodewijk
Quality Manager Ferm Global
GB
D
NL
F
E
P
I
S
FIN
N
DK
15
Werbung
Inhaltsverzeichnis
