Herunterladen Inhalt Inhalt Diese Seite drucken

GIULIANO S 560 Installation, Bedienung Und Wartung Seite 30

Universelle lkw-reifenmontiergerät
Inhaltsverzeichnis

Werbung

H
17
SMONTAGGIO
Lo smontaggio di pneumatici tubeless può avvenire in due modi:
1) Se la ruota non presenta difficoltà di smontaggio proseguire, dopo
la stallonatura, spingendo con il disco
stallontore sul fianco interno del pneumatico fino a far uscire i due
talloni dal cerchio (vedi fig. H).
2) Se la ruota è del tipo SUPERSINGLE, o comunque è particolar-
mente dura e pertanto non è possibile agire come descritto al punto
1, si rende necessario l'utilizzo dell'utensile a becco operando nel
modo seguente:
- Traslare il braccio portautensile sul fianco esterno
pneumatico.
Portarsi con la colonnetta mobile in posizione di
lavoro C.
-Ruotare la ruota e contemporaneamente fare avanzare l'utensile a
becco inserendolo tra cerchio e tallone finchè non si sia ancorato al
tallone stesso (vedi Fig. I).
-Allontanare di circa 4-5 cm. il cerchio dall'utensile in modo da evitare
l'eventuale sgangio del tallone dall'utensile stesso.
-Translare verso l'esterno l'utensile a becco in modo da
portare il suo punto rosso di riferimento in prossimità
del bordo esterno del cerchio.
Portarsi con la colonnetta mobile in posizione di
lavoro B.
- Inserire la leva (17, Fig. I) tra cerchio e tallone sulla destra
dell'utensile.
- Mantenendo la leva premuta abbassare la ruota fino a portare il
bordo del cerchio ad una distanza di circa 5 mm. dall'utensile a becco.
- Girare la ruota in senso antiorario mantenendo premuta la leva fino
alla completa fuoriuscita del tallone.
- Allontanare il braccio porta utensile in posizione di fuori lavoro e
traslarlo sul lato interno della ruota.
Portarsi con la colonnetta mobile in posizione di
lavoro D.
- Girare l'utensile a becco di 180°, inserire il medesimo tra cerchio
e tallone (vedi fig.L) e traslarlo fino a che il tallone sia in prossimità
del bordo anteriore del cerchio ( é consigliabile fare quest'ultima
operazione ruotando contemporaneamente la ruota).
- Allontanare di circa 4-5 cm. il cerchio dall'utensile in modo da evitare
l'eventuale sgangio del tallone dall' utensile stesso.
I
DEMOUNTING
Tubeless tyres can be demounted in two ways:
1) If the tyre is not difficult to demount, once the beads have been
loosened, use the bead disk to push against the inside plane of the
tyre until both beads come off the rim (See Fig. H).
2) With Supersingle or very hard tyres the procedure described above
cannot be used. The hook tool will have to be used as follows:
- Transfer the tool carrier arm to the outside plane of the tyre.
d e l
Take the mobile control unit to work position C.
- Rotate the wheel and at the same time move the hook tool forward
inserting it between rim and bead until it is anchored to the bead
(See Fig. I).
-Move the rim 4-5 cm from the tool taking care that it does not unhook
from the bead.
-Move the hook tool towards the outside until the red reference dot
is by the outside edge of the rim.
Take the mobile control unit to position B.
- Insert lever (17, Fig. I) between rim and bead at the right of the tool.
-Press down on the lever and lower the wheel to bring the edge of
the rim about 5 cm from the hooked tool.
-Turn the wheel anticlockwise pressing down on lever until the bead
is completely off.
-Move the tool carrier arm to its non-working position and then move
it to the inside plane of the wheel.
Take the mobile control unit to work position D.
-Turn the hook tool 180° and insert it between rim and bead (see Fig.
L). Move it until the bead is by the edge of the rim (best to do this
with the wheel turning).
-Move the rim about 4-5 cm from the tool making sure the hook does
not detach from the rim.
30

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis