Upgrading The Wheel Aligner Software; Ambient Conditions In The Place Of Operation - ATH-Heinl ATH-Lux 3D Bedienungsanleitung

- Assemble the column (7, Fig 1), consisting of 2 parts.
- Install the shelf (2, fig.1).
- Install the PC Box (4, fig.1) and insert the PC.
- Remove the rear panel of the column.
- Connect the USB hub (HUB, Figure 2) to a free USB
port on the back of the PC.
- Install keyboard, mouse and printer by connecting
to the USB HUB (HUB, fig.2).
- Install the monitor stand to the monitor and mount
them on the column (1, Figure 1), using the provided
screws.
-Connect the printer to the main supply via the power
strip located inside the bottom of the column.
-Connect the monitor to the PC and the power supply,
through the power strip located inside the bottom of
the column.
- Mount the beam (6, Figure 1) using the provided
screws.
- Connect the camera movement control cable
(CM, Fig. 2) to the Camera Movement main electric
box.
From the lower opening of the Beam out of 4 USB type
cables and 1 power type.
Bring 4 USB cables inside the PC Box through the rear
hole (L1-C1-L2-C2, Fig. 2).
- Connect the 2 camera USB cable with 2 USB ports on
the back of the PC (C1-C2, Figure 2).
- Connect the 2 USB cables with molded ferrite (Light
indications cards) to the USB HUB (L1-L2, Figure 2).
- Connect the Beam power cord to +12 V switching
power supply output (PS, Figure 2), paying attention
to the polarity (BROWN wire = +12 V, BLUE wire =
GROUND).
- Connect the switching power supply to the power
supply (PS, Fig. 2).
- Connect the PC to the mains supply (Fig. 2) via the
strip placed inside the lower part of the column.
- Connect the cables with the aid of the wiring diagram
(Fig. 40); all the plugs are clearly indicated on their
respective PC sockets. Push the plugs in completely
without straining and, where applicable, tighten the
lock screws.
- The aligner wheel is factory-set to operate with a
mains voltage of 230Vac. The wheel aligner may be
configured to operate with a mains voltage of 115Vac.
- Refit the rear panel of the column, fastening with the
specific tool provided.
- Connect the power supply cable to the plug provided;
first read the "Electrical Hook-up" section.
- Turn on the aligner with the main switch and the
® U Ath-h
rheberrecht einl
6
G h & c KG, A r
mb o lle echte vorbehAlten
monitor and the printer with the specific switches.
- Update the wheel aligner software if necessary,
"Updating the Wheel Aligner Software" section,
and install any optional kits, "Installing Additional
Functions" section.
Software protection key
installation
Insert the software protection key supplied in a free
USB port of the USB HUB (SP, Figure 2). The software
protection key is required to use the aligner.
CAUTION
For additional information about the technical
characteristics, warnings, maintenance and any
other data about the monitor or the printer, read
the relative operator's manuals supplied with
machine documentation.

Upgrading the wheel aligner software

The wheel aligner is supplied with the software already
installed, and is complete with an installation CD-ROM.
After installing the wheel aligner, switch on the machine
and go to the starting screen.
Press the key combination È + F12 (upper case + F12):
the software version will appear on the top left of the
screen, beneath the logo.
Compare the software release (indicated as "SW STD
...") with that stated on the installation CD-ROM supplied
with the aligner.
If the CD-ROM release is more recent than the release
installed, update the aligner software.
Detailed information about the software update procedure
is provided in the leaflet accompanying the CD-ROM.
AMBIENT CONDITIONS IN THE PLACE
OF OPERATION
• Relative humidity: 20% ÷ 90% (without condensation)
• Temperature range: 0°C ÷ 35°C
WARNING
The machine must not be operated in a potentially
explosive atmosphere.
/ D
rUcKfehler UnD technische
s : 2022-01, P
tAnD roDUKthersteller
Ä /
nDerUnGen vorbehAlten
Ath-h G h & c KG
einl mb o