Additional Main Or Secondary Monitors; Default Button Settings; General Button Programming Warnings - Comelit Magiskit 8472MC Technisches Handbuch

DIP S2
DIP 1 DIP 2 DIP 3 DIP 4 P1
0 0 0 0
CCS
1 0 0 0
ACT
0 1 0 0
INT
1 1 0 0
ACT
0 0 1 0
ACT
1 0 1 0
INT
0 1 1 0
1 1 1 0
INTb
0 0 0 1
CCS
1 0 0 1
0 1 0 1
CCP
1 1 0 1
PAN
0 0 1 1
1 0 1 1
INT
0 1 1 1
NULL
1 1 1 1
Lock- release
A
Speech
ACT Actuator
AI Self-ignition
Main switchboard call
CCP

General button programming warnings

If the default settings (see table on page 26) do not refl ect requirements, the
buttons can be programmed differently by carrying out the steps below.
At the end, set S2 DIP switches 1-2-3-4 to the combination 1111 (PROG
setting in the confi guration tables on pages 26,27,28,29).
26 26

Additional main or secondary monitors

Secondary Monitor
Main Monitor

Default button settings

P2 A
AI
AI
A
AI
CCS
ACT ACT
ACT
AI D
INT
PAN
A
K CCS
K
CCP
D INTb
INT
NULL NULL NULL
CCS
K
D
PAN
INT
The setting of S2 DIP 8 defines whether the bracket in question will be
managed as main (M) or secondary (S).
The external unit can manage up to a maximum of 4 door entry monitors
or door-entry phones for each call button.
In the classic Magis Kit configuration, it is therefore possible to have at
most 2 secondary door entry monitors and 2 main door entry monitors for
each call button, all powered by the same Art. 1205/B.
It is possible to manage up to 3 main door entry monitors within the same
family unit (i.e. set to the same user code). In this particular configuration,
the additional main door entry monitors must each be powered by the
special Art. 1212/B (see variant MSK/HCA and MSK/IC, page 120, 121).
When a call is made from the external unit, the monitor switched on will be
the main door entry monitor.
Any other secondary monitors in the same family unit will remain off.
When responding to a call from the external unit using a secondary door
entry monitor, the image is automatically displayed on the monitor.
At this point, the main door entry monitor switches off and the image
appears on the door entry monitor on which the 2 Self-ignition / Video
request button was pressed.
To display the image without activating audio communication with the
external unit, press the 2 button - Self-ignition / Video request.
with Art. 6433, 6434
P3 P4
ACT D
INT INTb
INTb ACT
CCP PAN
ACT ACT
CCS CCP
K CCS
AI INT
D AI
PAN CCP
PAN ACT
CCS K
INT ACT
INT INT
NULL NULL
PROG
Legend
Switchboard call
Guardian door-entry phone
call
Doctor
Panic
Programmable intercom,
general or selective
- standard single-family calling
for KIT and Simplebus Top
In this dip switch setting, the buttons control the programmed functions;
the NON-programmed buttons control functions referred to on line 0000
(see table on page 26). Restore the user code setting on S1, see table A
on page 25.
P5 P6
PAN K
D CCS
CCS CCP
K D
ACT ACT
INTb PAN
CCP INTb
PAN D
INT INTb
AI INT
INT AI
ACT D
AI CCS
INT INT
NULL NULL
Two-family intercom
INTb
- for KIT only
No function
NULL
Programmed functions,
see pages 26-27-28-29
In this Dip switch setting, the
PROG
buttons control the programmed
functions; the NON-programmed
buttons control functions
referred to on line 0000