System Set Up - HITEC X1 Pro Bedienungsanleitung

13. System Set Up

When the X1 Pro is powered on for the fi rst time all system
settings will be set to default. Each parameter can be adjusted
by the user, allowing for greater control of the charge process
for the specifi c battery being charged. When you power on
the X1 Pro you will be at the "
screen. Toggle up until you see "
Rest Time
During the charge>discharge or discharge>charge cycle,
batteries increase in temperature. The Rest Time program
allows the user to specify the time delay between cycles,
allowing time for the battery to cool.
Toggle right
Rest Time
CHG>DCHG 8Min
see the "
Toggle right once and the timer value will begin
fl ashing. Toggle up or down
The timer can be set to 0 to 60 minutes. Toggle right
once to set the Rest Time.
Safety Timer
When the charge process starts, the integrated safety
timer starts to run simultaneously. If an error occurs or the
termination circuit cannot detect whether the battery is
fully charged or not, the X1 Pro is programmed to prevent
overcharging and will terminate the charging process.
Safety Timer Calculation
When charging NiCd or NiMH batteries, divide the capacity
by the current, then divide the result by 11.9. Set this number
of minutes as the setting for the safety timer setting. If the
charger stops at this time threshold, about 140 % of the
capacity will have been fed into the battery.
Toggle up
SAFETY TIMER
ON 120Min
" SAFETY TIMER
Toggle right once and " ON " or "
Toggle up or down once to change this setting. Toggle
right once and the timer value will begin fl ashing. Toggle
up or down to adjust the timer value. Toggle right
once to set the Safety Timer.
Capacity Cut-Off
This program provides a maximum capacity protection function.
If the delta-peak voltage can not be detected or the Safety
Timer times out, the charge process will stop automatically
when the battery reaches the user-set maximum charge
capacity in order to prevent accidental overcharging.
44
PROGRAM SELECT "
SYSTEM SET-> ".
once and you will
" screen.
REST TIME
to adjust the timer value.
until you see the
" screen.
OFF " will begin fl ashing.
Professional Balance Charger, Discharger
Toggle up
Capacity Cut-Off
ON 5000mAh
see the "
OFF " screen. Toggle right
will begin fl ashing. Toggle up
this setting. Toggle right once and the amperage value
will begin fl ashing. Toggle up
amperage value. Toggle right
Cut-Off.
Key Beep & Buzzer
A beep sounds to confi rm the user's operation every time a
button is pressed. The buzzer or melody sounds at various
times during an operation to confi rm a different mode change.
Toggle up
Key Beep ON
Buzzer ON
see the "
screen. Toggle right once and (Key Beep) "
will begin fl ashing. Toggle up
this setting. Toggle right once and (Buzzer) "
" " will begin fl ashing. Toggle up
OFF
to change this setting. Toggle right
Beep and Buzzer settings.
Input Power Low Cut-Off
This function monitors the voltage of the input source used
to power the charger. If the voltage drops below the user
setting, the program will end forcibly to protect the input
source.
Toggle up
Input Power Low
Cut-off 10.0V
see the "
LOW CUT-OFF " screen. Toggle right
voltage value will begin fl ashing. Toggle up
to adjust the voltage value. Toggle right
Input Power Low Cut-Off.
External and Internal Temperature
Toggle up
Ext. Temp 0C
Int. Temp 20C
see the "
INT. TEMP . " screen. This screen shows the external
temperature of the battery and the internal temperature of
the charger. The battery temperature reading requires a
temperature sensor that is sold seperately.
Load Factory Set
This screen shows the external
LOAD FACTORY SET
ENTER
temperature of the battery and
the internal temperature of the charger.
once and you will
CAPACITY CUT-
once and " ON " or "OFF"
or down once to change
or down to adjust the
once to set the the Capacity
once and you will
KEY BEEP BUZZER "
ON " or " OFF "
or down once to change
ON " or
or down once
once to set the Key
once and you will
INPUT POWER
once and the
or down
once to set the
once and you will
EXT. TEMP AND