Special Features - HITEC X1 Pro Bedienungsanleitung

3. Special Features

Compact and Unique Design
The X1 Pro is a super-compact, portable charging system
with a unique design that incorporates a joystick input
device for very simple operation.
Two DC inputs
There are two DC inputs, one is located on the right side
of the charger and the other is located in the bottom for
docking into the ePowerBox 17A (230 W 13.8 V Switch DC
Power Supply-Part No. 44216).
Optimized Operating Software
The X1 Pro "AUTO" feature sets the charge and discharge
current for you automatically, preventing overcharging
which can damage your battery. In the event of an error,
the X1 Pro instantly disconnects the circuit and sounds an
alarm. This feature can be set by the user and controlled
through the two-way link for maximum safety.
Internal Independent Lithium Battery Balancer
The X1 Pro features a built-in cell voltage balancer so you
don't need to fuss with external balancers while charging.
Balancing Individual Cells During Discharging
The X1 Pro also monitors and balances each cell in the
pack individually while discharging. If the voltage of any
single cell is abnormal, the X1 Pro will display an error
message and the process will end automatically.
Adaptable to various types of lithium batteries
The X1 Pro will charge and discharge a variety of Lithium
batteries, such as Li-ion, LiPo and the new LiFe series of
batteries.
Fast and Storage Mode of Lithium Batteries
The X1 Pro features two styles of charging. "Fast" charge
reduces the charge duration while "Store" controls the
fi nal voltage of your battery, to optimize your packs for
long term storage and maximum lifespan.
Cyclic Charging/Discharging
A battery can be cycled 1 to 5 times consecutively. This
process is good for refreshing and balancing your battery.
Battery Memory
For your convenience, the X1 Pro will store the data pertaining
to a specifi c charge program for up to 10 batteries. Being
able to save and load these settings for a specifi c battery
saves the user lots of time.
30
Professional Balance Charger, Discharger
LiPo Battery Meter
The user can check a battery's total voltage, the highest
voltage, the lowest voltage and each cell's voltage.
Re-Peak Mode of NiMH/NiCd Battery
In Re-Peak Charge mode, the charger can peak charge the
battery 1-3 times consecutively. This is good for making
certain the battery is fully charged, and for checking how
well the battery receives fast charges.
Delta-Peak Sensitivity for NiMH/NiCd
This automatic charge termination program is based on the
principle of delta-peak voltage detection. When the battery's
voltage exceeds the threshold, the charging process will be
terminated automatically.
Automatic Charging Current Limit
The charging current can be set by the user when charging
NiCd or NiMH batteries. The 'AUTO' charging mode, however,
is recommended when charging NiMH batteries with low
impedance and capacity.
Capacity Limit
The charging capacity is always calculated as the charging
current multiplied by time. The charging process will terminate
automatically if the charging capacity exceeds the limit set
by the user.
Temperature Threshold
The battery's internal chemical reaction will cause the
temperature of the battery to rise. The charging process
will terminate automatically if the charger's temperature
exceeds the limit set by the user.
Processing Time Limit
Protect your battery by setting a maximum time limit for
charging and discharging.
PC Control Software "Charge Master"
The free "HiTEC Charge Master" software gives you unpar-
alleled ability to operate the charger through the computer.
You can monitor pack voltage, cell voltage and other data
during charging and view charge data in real-time graphs.
You can also initiate processes, control charging and up-
date fi rmware from the "HiTEC Charge Master" software.
When your charger is connected to a computer, the
"Charger Master" takes over the control of your charger.
You can control and operate the charger via the "Charger
Master" only.