Lithium - Charge Modes; Lithium - Charge Mode - HITEC X1 Pro Bedienungsanleitung

Professional Balance Charger, Discharger

7.1. Lithium - Charge Modes

The X1 Pro offers the following lithium charge modes:
Charge, Balance Charge, Fast Charge, Storage and Discharge.
Before selecting a charge mode, it is critical
that you select the correct type of lithium
battery to be charged. Failure to do so can
result in damage to the battery and possible
explosion.
Selecting a Battery Type
When you power on the X1 Pro
LiPo BALANCE
8.1A 22.2V(6S)
you will automatically be taken
to the " LiPo BALANCE " screen. If this is not the battery
type you wish to use, toggle left
once to enter the "
PROGRAM SELECT
LiPo BATT
GRAM SELECT
up or down until you see the battery type you wish to
charge.
Now, toggle right
LiPo BALANCE
8.1A 22.2V(6S)
enter the "
default charge mode will be "

7.2. Lithium - Charge Mode

Before you begin charging your battery, make
sure you have read and understand all of the
warnings and safety information.
In the charge mode, lithium batteries can be
charged without the use of a balance adaptor.
A balance adapter can be used, but it is not
required. Balance charge mode is recommended
for any battery with a balance lead.
See page 31 for the appropriate charging connections
setup for this operation.
First, select the correct battery type
LiPo CHARGE
8.1A 22.2V(6S)
by following the instructions on
page 33. Once you have set the correct battery type, toggle
up or down until you see the "
PRO-
" screen. Toggle
once to
LiPo " Program. The
BALANCE ".
LiPo CHARGE " screen.
7.2. Lithium - Charge Mode
Toggle right
LiPo CHARGE
0.8A 22.2V(6S)
amp rate value will begin fl ashing.
Toggle up or down to adjust the value to the desired
rate. Follow the instructions provided with your battery
when setting the amp rate.
Toggle right
LiPo CHARGE
0.8A 11.1V(3S)
cell count value will begin
fl ashing. Toggle up or down
This will automatically change the voltage value to the
correct setting for the selected cell count. The cell count
should exactly match the battery label.
Toggle and hold the joystick to the right
seconds and you will see " BATTERY CHECK WAIT...
followed by the " CONFIRM/CANCEL
This screen displays the number
R:3SER S:3SER
CONFIRM(ENTER)
of cells you set up as "
the number of cells detected by the processor as "
both numbers are identical, you may toggle right
confi rm and begin charging. If the cell count does not
match, toggle left once to return to the previous screen
and carefully check the number of cells of the battery pack
before proceeding.
Once charging has commenced, the
Li3s 1.2A 12.69V
CHG 022:43 00682
charger will display the following
real-time information: battery type/cell count, charging current,
battery voltage, charging time and charged capactiy.
During charging, the battery should be placed
inside a fi reproof/retardant bag and on a fi re
proof surface, away from other combustible
objects.
If you are using a balance adaptor,
4.09 4.09V 4.09V
0.00 0.00V 0.00V
during charging you may toggle
up once to view the voltage of each individual cell.
Once the battery is fully charged the screen will read
" [END:FINISH] " and the charger will emit a chiming
sound. Toggle left once to stop charging. You may toggle
left at any time during the charging process to stop
charging.
once and the
again and the
to adjust the cell count.
for three
"
" screen.
R " and
S ". If
once to
33