Electric Connection; Cleaning - Scheppach FS850 Originalbetriebsanleitung

Replacing the diamond cutting wheel (Fig. 10- 12)
Attention! Pull out the mains plug
1. Loosen the 2 bolts (F) and take out the saw blade
protection (20). (Fig.10)
2. Place the wrench (21) on the motor shaft and
keep it there.
3. Loosen the flange nut in the running direction of
the cutting disc (10) with the wrench (22).
4. Remove the outer flange (23) and cutting disc
(10). (Fig.11)
5. Clean the supporting flange carefully before in-
stalling the new cutting disc.
6. Insert the cutting disc in the reverse sequence
and tighten it. Caution: Pay attention to the run-
ning direction of the cutting disc!
7. Reinstall the saw blade protection (20).

Electric connection

Check electric cables regularly for damage. Ensure
that during the check, the connecting cable is not
connected to the mains.
Electric connecting cables must conform to the com-
mon VDE- and DIN provisions. Only use connecting
cables with the H 07 RN designation.
Keeping a copy of the type designation on the con-
necting cable is a specification
Damaged electric connecting cables
Insulation damages frequently occur on electric con-
necting cables. The reasons are:
• Pressure points, if connecting cables are routed
through window or door gaps.
• Kinks due to improper mounting or routing of con-
necting cables.
• Intersections due to overruns of connecting cables.
• Insulation damage due to pulling out from wall
sockets.
• Cracks due to ageing of insulation.
Such damaged electric connecting cables should not
be used and can be fatal because of the insulation
damage
AC motor 230 V/ 50 Hz (Fig. 12)
Mains voltage 230 Volt / 50 Hz.
Mains connection and extension cable must have
3-wires = P + N + SL. - (1/N/PE).
Extension cables must have a minimum cross-sec-
tion of 1.5 mm².
The mains connection is secured with a max. 16A fuse.
Start-up of the leakage current circuit-breaker
(Fig. 13):
• The function should be checked before each start-
up and at regular Intervals (min. once every week).
• If the leakage current circuit-breaker does not
switch off properly during this test, there is no per-
sonal protection! The device must therefore be
switched off immediately!
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• In case of damages caused by the non-observation
of this operating instructions manual, all warranty
claims will become null and void. We do not accept
any liability for consequential damages.
• Check the product for damage before each use! If
you detect a damage, do not connect the product to
the mains power supply!
• After actuating the orange Reset button, the device
is ready for operation. Before operation, please test
the triggering with the help of the Test button (as
described in "Operation").
• Insert the leakage current circuit-breaker into the
socket.
• Press the orange Reset button.
• A red symbol is displayed in the window indicating
operational readiness.
• Press the red Test button. This action simulates a
leakage current.
• If the machine is working properly, the circuit-break-
er will disconnect the load from the mains. This is
displayed in the window through the disappearance
of the red symbol.
• Protection of man and animal is effective only if the
machine works properly.
• The Reset button must be pressed a second time
for operation.
• The load can now be inserted.
Technical data:
Triggering leakage current: < 30 mA
Power supply: 230V~/50Hz
Load capacity: 16A (3680W)
Number of pins: 2-pin wired
Preliminary fuse: 16 A
Protection type: IP54
Dimensions: 126x50x88mm
USE ACCORDING TO MANUFACTURER'S IN-
STRUCTIONS!
The portable leakage current circuit-breaker is de-
signed for wet grinding machines and similar elec-
trical loads in the household.
It is simply connected between the mains power sup-
ply and the load, and therefore offers optimum pro-
tection against physical contact with live components
and sudden restart of the machine after restoration
of power.
Always operate the machine with the provided leak-
age current circuit-breaker installed.

11. Cleaning

Caution! Pull out power plug.
Clean the machine after each work cycle.
GB | 25