Configuring An Effect Module; 5�7�2�1 Modulation; 5�7�2�2 Delay - IMG STAGELINE DELTA-160 Bedienungsanleitung

To insert effect modules into a signal bus or the sum channel:
1) Tap  under "Busses"� A list will appear� Select a signal bus or the
sum channel from this list� In both fields on the left of the list, the
modules currently inserted into this channel will appear�
2) To add or change a module, tap the field� The field will have a
yellow frame�
3) Tap a module at the top to select the module to be inserted�
Note: If this model is already being used at another location, a message will
appear showing the location where it is currently being used� In this case,
determine if a change to the new location is to be forced ("Yes") or not ("No")�
If not, select the other module of the same type if required�
4) To remove the effect, tap the field twice�
5) Repeat these steps for other channels or modules if required�

5.7.2 Configuring an effect module

To configure the effect characteristics of a module, tap the button of
the module in the effect processor view (fig� 21)� Alternatively, keep
your finger for a while on the button of the module in the Insert
section of the corresponding channel view� The configuration view
of the corresponding effect module will appear�
When all settings have been made, tap �� to close the inner window
or tap  or  to configure another effect module�
5.7.2.1 Modulation
Modul1
Setup
EQ LS
Patch
+18
Meter
0
FX
−18
20 200
Scenes
Recorder
Gain Freq
Monitor
0.0 dB 100.0 Hz
Fig. 22 Effect modules "Modulation"
Setup options:
– type of effect under "Type ... "
Slow Chorus
Slow Flanger
Slow Celeste
Slow Rotor
– ratio between original signal "Dry" and effect signal "Wet"
– modulation frequency "Speed / Rate"
– modulation depth "Intensity"
– equalizer with low-shelf filter "EQ LS" (20 – 200 Hz, ±18 dB) and
high-shelf filter "EQ HS" (1�5 –15 kHz, ±18 dB), each with adjustable
cut-off frequency "Freq" and gain / attenuation "Gain"
Note: To adjust average values, tap the numeric fields twice�
– "Save" to save effect settings (cf� chapter 5�3�3�1)
– "Lib ... " to retrieve effect settings that have been saved
(cf� chapter 5�3�3�2)
40
Lib My_Mod Save Type
Dry
EQ HS
+18
0
Speed
50
−18
20k 20 200 20k
Intensity
100.0
Gain Freq
0.0 dB 6.30 kHz
Fast Chorus
Fast Flanger
Fast Celeste
Fast Rotor
5.7.2.2 Delay
Setup
Patch
Meter
FX
Scenes
Recorder
Monitor
Fig. 23 Effect modules "Delay"
Setup options:
– type of effect under "Type ... "
Three Echo 1/16
Four Echo 1/16
– ratio between original signal "Dry" and effect signal "Wet"
– "Tempo": speed of a music piece in beats per minute (BPM)
– setting the "Tempo": tap "Tap Tempo" rhythmically to the beat of
2019/08/23
X
07:50:01 a music piece as an alternative to making the setting via the control
knob; when the option "Use Back" is selected, the key BACK (5)
X
Slow Chor
can also be used for tapping
Wet
100.0
– multiplication "Factor" of the beat interval defined by "Tempo" to
determine the "Delay Time"
Rate
100.0
– "Delay Time" resulting from the setting of "Tempo" and "Factor":
120 200
Delay Time [ms] ≈ Factor × 60 000 × 1 ⁄ Tempo
– "Feedback" (feedback effect part); defining the number of repeats
– equalizer with low-shelf filter "EQ LS" (20 – 200 Hz, ±18 dB) and
high-shelf filter "EQ HS" (1�5 –15 kHz, ±18 dB), each with adjustable
cut-off frequency "Freq" and gain / attenuation "Gain"
Note: To adjust average values, tap the numeric fields twice�
– "Save" to save effect settings (cf� chapter 5�3�3�1)
– "Lib ... " to retrieve effect settings that have been saved
(cf� chapter 5�3�3�2)
Delay1 Lib My_Delay
EQ LS EQ HS
+18 +18
0 0
−18 −18
20 200 20k 20 200
Gain Freq Gain
0.0 dB 100.0 Hz 0.0 dB
One Echo 1/4 Two Echo 1/8
Three Echo 1/16 Delayed
One Echo 1/4 with 4 Reflect
2019/08/23
X
07:50:01
X
Save Type One Echo
Dry Wet
100.0
Factor
1
20k
Use Back
Delay Time Tempo
Tap
Tempo
1.0ms 80BPM
0.0
Feedback
Freq
0 45 90
6.30 kHz