Crossover Network; System Configuration; Resetting The Mixer To The Factory Settings; Setting The Date And The Time - IMG STAGELINE DELTA-160 Bedienungsanleitung

6.5 Crossover network

The mixer is equipped with a crossover network that is used to send
a low-bass signal for operating subwoofer speakers� For this purpose,
a low-pass filter can be activated for Bus 8� Regardless of this, the
signal of the sum channel L / R MIX OUTPUT can be cut off in the
low-frequency range so that the signal will be split to the two ways�
Requirements:
– All input channels whose input signals are also to be sent to the
subwoofer must not only be assigned to the sum channel but also
☞
to Bus 8 ( chapter 5�2�2)�
– Bus 8 must be assigned to the outputs which are connected to the
amplifier inputs of the subwoofers (
– If only a mono subwoofer is to be used, the mono sum of the signal
can be created via the function "Sum" of Bus 8 (
Input L /R MIX
Channel OUTPUT
MIC1 L &R
Stereo
Bus
MIC12 Bus 8
Fig. 30 Configuration example for a crossover network
To adjust the crossover network:
1) Press the key SETUP (5) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
system settings� The settings for the crossover network can be
found in the lower section (fig� 31)�
3) Under "Crossover", activate the low-pass filter for "BUS 8" and,
if required, the high-pass filter for "Master LR" via the buttons
"IN"� When the filter has been activated, the button will be blue�
Information
Setup
System Version:
4) Tap the corresponding control displayed on the screen and use
Apk: V1.6.1
Patch 1.3.0 -5B 0.662V
the control knob ADJUST (6) to set the cut-off frequency for the
Serial: 000000000000090c
filter selected�
aa3798d700000000
Meter
IP Address:
For a filter slope of 24 dB / octave, the adjustment range is 40 – 300 Hz�
IP Address:
Note: The filters will not affect the signals switched to the solo bus�
FX
5) To exit the setup menu, press the key SETUP�
Brightness
Scenes
Recorder
BUS 8
Monitor
80.0 Hz
Fig. 31 Crossover network
44
☞
chapter 5�2�4)�
☞
chapter 5�2�2)�
Cross- Output
over Patch
OUT 7
OUT 8
HPF
OUT 5
Sub
OUT 6
LPF
2019/08/23
07:50:01
Sample Rate
48.0 kHz
Maintenance
44.1 kHz
Delay Unit
ms ft m
Setup
Crossover
Master LR
System Version:
IN IN
80.0 Hz
Patch
Meter
IP Address:
IP Address:
FX
Brightness
Scenes
Recorder
Monitor

7 System Configuration

7.1 Resetting the mixer to the factory settings

The mixer can be reset to its factory settings if required� All settings
made by the user will be lost� Therefore, to preserve your own settings,
make a backup of the corresponding scenes to an external USB storage
☞
device ( chapter 5�8) or export all settings (
resetting� After resetting, the exported settings can be imported into
the mixer again�
1) Press the key SETUP (5) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
system settings (fig� 26)�
3) Under "System", tap the button "Maintenance"� A view with
various system functions will appear�
4) To reset the mixer to the factory settings, tap the button "Factory
Reset"� Confirm the security prompt with "Factory Reset" or cancel
with "Cancel"�
The mixer will switch off and restart with the factory settings�

7.2 Setting the date and the time

A correct time setting is important for the management of scenes�
To set the current time:
1) Press the key SETUP (5) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
system settings (fig� 26):
3) Under "System", tap the button "Maintenance"� A view with
various system functions will appear�
4) Tap the button "Time Settings"� The view for setting the time will
appear�
5) Make the settings and confirm with "Save"�
X
6) Press the key BACK (5) to exit the setup maintenance submenu�
System
7.3 Changing the unit of measurement for signal delay
For signal delay (DELAY), enter either the delay time (ms) or alterna-
tively the distance (m or ft), e� g� the distance between two speakers
or microphones� The delay time will be automatically calculated from
Setup Wifi
this value (speed of sound: 343 m / s)�
To change the unit of measurement:
1) Press the key SETUP (5) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
Information
system settings�
Apk: V1.6.1
3) Under "Delay Unit", tap the corresponding unit (fig� 32)�
1.3.0 -5B 0.662V
4) To exit the setup menu, press the key SETUP�
Serial: 000000000000090c
aa3798d700000000
Fig. 32 Unit of measurement for signal delay
Crossover
BUS8
IN
80.0 Hz
2019/08/23
07:50:01
Sample Rate System
48.0 kHz Maintenance
44.1 kHz
Delay Unit
Setup Wifi
ms ft m
Master LR
IN
80.0 Hz
☞
chapter 5�8�4) before
X