5�2�2�2 Settings For A Bus Selected - IMG STAGELINE DELTA-160 Bedienungsanleitung

channels) or its stereo balance (for stereo input channels) can be
set: Tap the numeric field underneath the Pre / Post Fader button
of the corresponding bus� The field will have a yellow frame� Use
the control ADJUST (6) to adjust the ratio between the left stereo
channel and the right stereo channel� To make it easier to reset the
setting to the centre position "50|50", tap the display field twice�
Mic IN
GEQ 2
48 V REV H PF
EQ
Bus 1 Bus 2 Bus 3
GATE COMP
PreFader PreFader PreFader
Bus 1
Bus 6 50|50
10 10 10 10
0 0 0 0
−10 −10 −10
CH 1
−20 −20 −20 −20
PAN
-1 dB
−30 −30 −30 −30
50/50
−40 −40 −40 −40
L&R
−50 −50 −50 −50
−∞ −∞ −∞ −∞
SOLO
MUTE
Fig. 9 Send view of an input channel
5.2.2.2 Settings for a bus selected
Input channels can also be assigned to a bus from the bus� It will,
however, not be possible to set the stereo balance of the input chan-
nels and to define where the signal is picked up (Pre Fader/ Post Fader)�
1) Press the key BUS 1– 8 (13)� The overview of the buses will be
displayed (fig� 10)�
A channel strip is displayed for each bus containing the following
information (from top to bottom):
– direct assignment of the bus signal to an output, e� g� "OUT 1"
( ☞ chapter 5�2�4)
– insert effects used for this bus, e� g� Mod 1, Rev 2 or GEQ 1
☞
( chapter 5�7�1); INSERT will be displayed if no effect has
been assigned to the insert point
– miniature curve of the parametric equalizer (
– input channels assigned to this bus including the signal part
adjusted (Send control); for stereo buses also the mono buses
assigned
– bus name ( ☞ chapter 6�1)
– volume adjustment for the bus (bar graph on the left)
– PAN (mono buses) / BAL (stereo buses) stereo position or stereo
balance of the bus signal
– assignment to the stereo sum "L&R"
– status indication ⓣ when the signal delay has been activated
– SOLO status and MUTE status; like the signal of an input channel,
a bus signal can be monitored via the SOLO key (11) (
ter 5�1�4)
– signal level (bar graph on the right)
CH1
Bus 4 Bus 5 Bus 6 Bus 7 Bus 8
PreFader PreFader PostFader PreFader PreFader
50 | 50 50 | 50 50 | 50 50 | 50 50 | 50
10 10 10 10 10 10
0 0 0 0 0 0
−10 −10 −10 −10 −10 −10
−20 −20 −20 −20 −20 −20
−30 −30 −30 −30 −30 −30
−40 −40 −40 −40 −40 −40
−50 −50 −50 −50 −50
−∞ −∞ −∞ −∞ −∞ −∞
☞
chapter 5�3�2)
OUT 1 OUT 2
Mod 1 GEQ 1 INSERT INSERT
EQ EQ
CH 1 CH 2 CH 1 CH 2
CH 5 CH 5
CH 7 CH 7
CH 10 CH 10
CH 11 CH 12 CH 11
X
L&R
Bus 1 Bus 2
−11dB PAN −11 dB PAN
50/50 50/50
L&R
SOLO SOLO
MUTE MUTE
Fig. 10 Overview of signal buses
2) Press the corresponding key SEL (10) to select the bus to be set�
The key will be illuminated and the channel strip in the view will
be highlighted�
3) The faders are used to set the volume for the buses�
4) To assign the input channels and to adjust the signal parts to be
routed from the input signals to the bus selected, press the key
SENDS (13) so that it is illuminated�
The keys M (12) can be used now to assign the corresponding
input channel to the bus selected or to revoke the assignment�
Press the key IN 1– 8 or IN 9 – 20 (13) to go to the corresponding
inputs if required�
5) The faders are used now to change the signal part of the corre-
sponding input� To quickly set the value 0 dB, press the key SOLO�
6) To assign the bus signals to the stereo sum and to adjust the signal
parts to be routed from the mono buses to the stereo buses, tap
the topmost section of the channel strip� The corresponding Send
view will be displayed (fig� 11)�
OUT 1
Mod 1 GEQ 1
EQ
CH 1 CH 2
Bus 5
CH 5
PreFader
CH 7
CH 10
50 | 50
CH 11 CH 12
10
5
0
Bus 1
−5
−10
−11 dB PAN
−20
50/50
−30
L&R
−40
SOLO −∞
MUTE
☞ Fig. 11 Send view of a mono bus
chap-
7) To assign the bus signal to the stereo sum, tap the button "L&R"
so that it will be displayed in colour�
8) When a mono bus has been selected, this mono bus can be as-
signed to one or more stereo busses via the corresponding button�
The point where the signal is picked up (Pre Fader/Post Fader) can
also be defined� To change the signal part or the stereo position
for assigning a bus, tap the corresponding element to select it and
then use the knob ADJUST (6) to make the setting�
9) The buttons underneath "Insert" are used to select one or two
insert effects of the internal effect processor for the bus (
ter 5�7�1)�
To set the stereo position / stereo balance of a bus signal or to define a
signal delay, tap the lowermost section of the channel strip� The view
shown in fig� 12 will be displayed�
OUT 3 OUT 4 OUT 5
INSERT INSERT INSERT INSERT INSERT INSERT INSERT
EQ EQ EQ
CH 1 CH 2 CH 1 CH 2
CH 3 CH 3
CH 5 CH 5 CH 5
CH 7 CH 7 CH 7
CH 10 CH 10
CH 12 CH 11 CH 11 CH 12
Bus 2 Bus 1
Bus 3 Bus 4
Bus 3 Bus 4 Bus 5 Bus 6
−11dB PAN −11dB PAN −11dB BAL −11dB
50/50 50/50 50/50
L&R
SOLO SOLO SOLO
MUTE MUTE MUTE
Bus 1
Send
Bus 6 Bus 7 Bus 8 L&R
PostFader PreFader PreFader
50 | 50 50 | 50 50 | 50 50 | 50
10 10 10 10
5 5 5 5
0 0 0 0
−5 −5 −5 −5
−10 −10 −10 −10
−20 −20 −20 −20
−30 −30 −30 −30
−40 −40 −40 −40
−∞ −∞ −∞ −∞
OUT OUT OUT 6
INSERT INSERT INSERT Rev 2 INSERT
EQ EQ EQ
CH 6 CH 5 CH 6 CH 5 CH 6
CH 12 CH 12 CH 12
Bus 1 Bus 1
Bus 7 Bus 8
BAL −11dB BAL +2 dB BAL
50/50 50/50 50/50
L&R L&R
SOLO SOLO SOLO
MUTE MUTE MUTE
X
Insert
Modul 1
Modul 2
Delay 1
Delay 2
Reverb 1
Reverb 2
GEQ 1
GEQ 2
☞
chap-
33