Yamaha RX-V3800 Bedienungsanleitung Seite 119

3
Refer to "Selecting the input source of Zone
2 or Zone 3", "Adjusting the volume level of
Zone 2 or Zone 3", "Adjusting the balance of
the speaker level in Zone 2 or Zone 3" or
"Adjusting the tonal quality of Zone 2 or
Zone 3" on page 118 to perform further
operations.
Remote control operations
Set the operation mode selector to D AMP
1
and then press B SELECT k repeatedly to
select the zone you want to control.
"ZONE 2" or "ZONE 3" is displayed in the display
window (B) on the remote control.
AMP
SOURCE
SELECT
TV
2
Refer to "Selecting the input source of Zone
2 or Zone 3", "Adjusting the volume level of
Zone 2 or Zone 3", "Adjusting the balance of
the speaker level in Zone 2 or Zone 3" or
"Adjusting the tonal quality of Zone 2 or
Zone 3" on page 118 to perform further
operations.
Press B SELECT k / n to exit from the
3
Zone 2/Zone 3 mode.
Turning on or off Zone 2 and/or Zone 3
using the remote control
9 POWER and 8 STANDBY on the remote control
work differently depending on the selected zone that
appears in the display window (B) on the remote control.
• When the main zone, Zone 2 or Zone 3 mode is
selected (see page 117), you can turn on the main zone,
Zone 2 or Zone 3 or set them to the standby mode
individually.
• When the all mode is selected, pressing 9 POWER
turns on the main zone, Zone 2 and Zone 3
simultaneously and pressing 8 STANDBY sets them
to the standby mode simultaneously.
or
Control mode Display window (B)
Main zone
Name of the selected
mode input area
"ZONE 2" or "2;name
Zone 2 mode
of the selected input
area"
"ZONE 3" or "3;name
Zone 3 mode
of the selected input
area"
All mode "ALL"
Notes
• When the remote control is in the main zone mode, "MAIN"
appears for a few seconds when 9 POWER or 8 STANDBY
is pressed.
• "ALL" appears in the display window (B) on the remote
B SELECT n is pressed.
control only when
Selecting the input source of Zone 2 or
Zone 3
Rotate the C INPUT selector on the front panel
(or set the operation mode selector to D AMP
and then press one of the input selector buttons
( 1 )) to select the input source of the selected
zone.
If the remote control is used to select the input source, "2;
name of the selected input area" or "3; name of the
selected input area" is displayed in the display window
(B) on the remote control when Zone 2 or Zone 3 is
selected respectively.
Notes
• The selected input sources are shared across all zones.
• If you set the recording source other than "SOURCE" (see
page 67), the input source of Zone 2 is fixed to the source you
set as the recording source.
• This unit does not display the iPod or network/USB menu on
the video monitor connected to one of the ZONE VIDEO jacks.
y
• You must complete this step within 10 seconds while the
selected zone flashes in the front panel display. Otherwise, the
currently selected zone mode is automatically canceled. In this
case, press Q ZONE CONTROLS on the front panel again.
• When a video monitor is connected to one of the ZONE VIDEO
jacks, you can display the control information of Zone 2 or
Zone 3 on the video monitor screen. Set "Zone OSD" to
"Zone2&Zone3" or "Zone2" (see page 93).
Using multi-zone configuration
POWER
and
STANDBY
Turns on the main
zone only or sets it to
the standby mode.
Turns on Zone 2 or
sets it to the standby
mode.
Turns on Zone 3 or
sets it to the standby
mode.
9 POWER: turns on
the main zone, Zone
2 and Zone 3.
8 STANDBY: sets
the main zone, Zone
2 and Zone 3 to the
standby mode.
117
En