Safety Warnings And Precautions - Mhouse GDX Serie Anweisungen Und Hinweise Für Die Installation Und Die Bedienung

NEVER touch parts of the automation while the door is moving!
• Before using the automation for the first time, take care to read this
operation manual provided by the automation installer. Also ensure that
you are fully informed of all origins of residual risks.
• Keep the manual for consultation when in doubt and ensure supply to
new owners of the automation.
• Your automation is a machine that performs commands imparted by the
user; negligent or improper use may constitute a hazard. Never activate
automation controls if persons, animals or objects are present in the oper-
ating range.
• Children: this automation system guarantees a high level of safety,
using special detection devices to prevent movement in the pres-
ence of persons or objects , thereby guaranteeing constant foresee-
able and safe activation. However, it is advisable to ensure that chil-
dren do not play in the vicinity of the automation. To avoid inadver-
tent activation, and remote controls should always be kept out of
reach. (the transmitter is not a toy!).
• Check the automation frequently to detect possible imbalance, signs of
wear or damage. Suspend use immediately if maintenance is required.
• Periodically check correct operation of the photocells and perform the
scheduled maintenance at least every six months.
The automation requires periodic maintenance to ensure optimal opera-
tion, extended lifetime and complete safety. Checks, maintenance and
repairs must be performed exclusively by qualified personnel.
Arrange with the installer to draw up a periodic maintenance schedule.
Nice recommends maintenance every 6 months in the case of normal
domestic use, but this interval may vary according to the intensity of use.
The user may and must perform periodic cleaning of the photocell lenses
and removal of any leaves or stones that may obstruct the automation.
With transmitter TX4
The transmitter keys have the following functions:
COMMAND ( )
*
Key T1
Key T2
Key T3
Key T4
( * ) This table must be compiled by the person who programmed the automation.
With safety devices disabled
In the event of safety devices malfunctioning or out of service, the door
may still be moved by means of the transmitter or keypad.
If a command is sent with safety devices out of service, the manoeuvre
does not start and the courtesy light flashes a few times. The number of
II – English
OPERATION MANUAL
(to be given to the final user of the automation)

SAFETY WARNINGS AND PRECAUTIONS

MAINTENANCE OPERATIONS ADMISSIBLE TO THE USER
TO CONTROL THE DOOR
• Photocells do not constitute actual safety devices, but safety aids. They
are designed using highly reliable technology, but in extreme conditions
may be subject to malfunctions or potential faults. CAUTION! – In certain
cases these faults are not immediately evident.
NEVER pass the transit area while the door is moving!
• If any anomalous condition is noted on the automation, disconnect the
power supply from the system immediately. Never attempt to repair the
automation alone; contact your local installer for assistance. In the mean-
time the system can be used with manual Opening and Closing by manu-
ally releasing the gearmotor as described in this manual.
• Even if you possess the skills, never modify the system or automation
programming and adjustment parameters: This is the responsibility of the
automation installer.
• Testing, periodic maintenance and any repairs must be documented by
the person performing the operations and the relative documents must be
kept by the system owner.
• At the end of the automation's lifetime, ensure that it is disposed by
qualified personnel and that the materials are recycled or scrapped
according to current standards in the place of use.
• For cleaning the surfaces of the devices, use a slightly damp (not wet)
cloth. Important – Never use substances containing alcohol, benzene,
diluents or other flammable substances. Use of these substances may
damage to the devices and cause fires or electric shocks.
• To prevent persons from activating the door, before proceeding with
cleaning, remember to release the automation as described in this manual.
flashes depends on the fault concerned; refer to Table 6 to locate the
cause of the problem.
Then, within 3 seconds, press and hold the command again until the door
starts to move in "hold-to-run" mode. This mode operates as follows:
while the command is pressed, the door continues to move and stops as
soon as the key is released.
Important – In the event of safety device malfunction, arrange for repairs
to the automation immediately.