Short Overview Of The Operation - IMG STAGE LINE DMX-1440 Bedienungsanleitung

9 Short Overview
of the Operation
Adjusting a scene
1) Select the control channel group(s) with but-
tons CTRL CHANNEL PAGE [1 . .12] to [85 . .96] .
2) Adjust the fader MASTER LEVEL to maximum
value .
3) Adjust the scene with the sliding controls (last
value must be "fetched" by the fader) .
4) If necessary, activate the control lever MOTION
CONTROL for coarse presetting (with STICK
CTRL ASSIGN 1 / 2 and/or 7/ 8: the LED below
the corresponding sliding controls lights up) .
Crossfading to another adjustment
1) Adjust the 1 scene .
st
2) Press button HOLD: LED HOLD / CROSSFADE
lights up .
3) Adjust the 2 scene .
nd
4) Adjust the crossfading time with the control
C .F . TIME .
5) Press button HOLD: the crossfading starts – or
crossfade manually .
Manual crossfading
1) Turn the control C .F . TIME to the right stop:
Display:
CF TIME: manu.
CROSSFADE lights up .
2) Set crossfader MANUAL CROSSFADE to an
end position .
3) Move the crossfader to the other end position:
The crossfading starts running . When reaching
the other end position, the crossfading stops .
Memorizing a scene
1) Adjust the scene .
2) Select the bank with buttons
ton BANK and numerical keys [0] [1] . . . [2] [0] .
3) Press button STORE .
4) Press the button for the scene [1] . . . [12] .
Calling a scene
1) Select the bank with buttons
BANK and numerical keys [0] [1] . . . [2] [0] .
2) Adjust the crossfading time with control
C .F . TIME .
3) Press the scene button [1] . . . [12]: crossfading
starts – or crossfade manually .
Flash buttons
Function FLASH CHANNEL
1) Press button FLASH MODE repeatedly until
the red LED FL . CH . lights up .
2) Select the control channel group(s) with but-
tons CTRL CHANNEL PAGE .
3) Keep the flash button (below the sliding con-
trols) pressed .
Function FLASH GROUP
1) Press button FLASH MODE repeatedly until
the yellow LED FL . GRP . lights up .
2) Keep the flash button [1] . . . [5] pressed .
Function SHOW VALUE
1) Press button FLASH MODE repeatedly until
the green LED SH . VAL . lights up .
2) Select the control channel group with button
CTRL CHANNEL PAGE .
3) Press the flash button: the display shows the
corresponding channel value .
Programming a flash group
1) Keep button FLASH MODE pressed and press
button STORE: LEDs FL . CH . and FL . GRP . light
up .
2) Select the channels with buttons CTRL CHAN-
NEL PAGE and the flash buttons .
3) Press button STORE: LED FL . CH . is extin-
guished, LED FL . GRP . is still illuminated .
4) Press the flash button [1] . . . [5] for the desired
group memory .
Changing a flash group
1) Press button FLASH MODE repeatedly until
the yellow LED FL . GRP . lights up .
2) Keep the corresponding flash button(s) [1]
. . . [5] pressed and press button STORE: LEDs
FL . CH . and FL . GRP . light up .
3) Select additional channels or cancel selected
channels (with buttons CTRL CHANNEL PAGE
and the flash buttons) .
4) Press button STORE: LED FL . CH . is extin-
guished, LED FL . GRP . is still illuminated .
5) Press the flash button [1] . . . [5] for the desired
group memory .
Run of a scene sequence
1) Press button SEQUENCE: The green LED RUN
lights up .
2) Select the sequence number with the numer-
ical keys [0] [1] . . . [6] [0] .
Time-controlled start
1) Specify the speed with control SEQUENCER
SPEED or press button TAP SPEED twice .
, LED MANUAL
2) If the selected sequence is not of type
(i . e . with memorized crossfading times), adjust
the crossfading time with control C .F . TIME .
3) To start, press button YES .
4) To change the direction, press button
ward) or
Music-controlled start
1) Press button AUDIO . Display:
The sequence starts by the audio signal of the
jack AUDIO IN or of the internal microphone .
or or but-
 
2) Match the sensitivity with control AUDIO
SENS .
3) If necessary, reduce the crossfading time with
control C .F . TIME .
4) To change the direction, press button
, or button
 
(backward) or
Manual start
1) If the selected sequence is not of type
(i . e . with memorized crossfading times),
adjust the crossfading time with control
C .F . TIME .
2) Press button
to advance one step (with current crossfad-
ing, the crossfading is stopped with the first
pressing, with the second pressing the next
step is called) .
Holding the run
(in case of time control or audio control)
1) To hold, press button HOLD .
2) To continue, press button YES or to interrupt,
press button NO .
Replacing a running sequence
by another sequence
1) Press button SEQUENCE .
2) Select a new sequence number with the nu-
merical keys [0] [1] . . . [6] [0] .
3) Start the new sequence with button YES,
AUDIO,
Stopping the run
1) Press button SEQUENCE repeatedly until LED
RUN is extinguished .
Programming a sequence
1) Press button SEQUENCE: The green LED RUN
lights up .
2) Press button STORE: The red LED PRG lights
up .

(backward) .

Audio Trig.
(forward) .

(forward) or (backward)
 
or .
 
3) Select the sequence number with the numer-
ical keys [0] [1] . . . [6] [0] .
4) Delete the sequence already programmed
with button DELETE, if necessary, and confirm
with button YES .
5) Select the sequence type: to memorize with
the crossfading time
crossfading time button NO .
6) Enter bank [0] [1] . . . [2] [0] and scene [0] [1]
. . . [1] [2] for the first step .
7) Memorize the scene with button STORE or
select another scene after pressing button NO .
8) In case of sequence type
crossfading time for this step with control
C .F . TIME and confirm with button STORE .
9) Enter further steps . Then stop the program-
ming with button SEQUENCE and change to
the sequence running mode (green LED RUN
lights up) or to the direct mode by pressing
again (green LED RUN is extinguished) .
Changing the sequence
1) Press button SEQUENCE, then button STORE .
Select the sequence number with the numer-
ical keys .
2) Attach new steps: Press button
scene as under "Programming a sequence"
+CFT
as from operating step 6) .
3) Change the scene of a step: Select the step
with button or

as under "Programming a sequence" as from
(for-
operating step 6) .
4) Change only the crossfading time of a step
(for sequence type
button or . With button
 
corresponding crossfading time . Adjust the
new crossfading time with control C .F . TIME
and confirm with button STORE .
5) Delete the sequence step: Select the step with
button or . Press button DELETE and
 
confirm with button YES .

6) Insert a sequence step: Select the step before
which a new step is to be inserted (
Press button INSERT . Enter the new scene as
+CFT
under "Programming a sequence" as from
operating step 6) .
7) After the modifications, change with button
SEQUENCE to the sequence running mode
(green LED RUN lights up) or to the direct
mode by pressing the button SEQUENCE again
(green LED RUN is extinguished) .
Configuring control channels
1) Call the menu with button ESC / SETUP .
– Menu item "Output Options" to change
the DMX address assignment and inversion
of DMX values
– Menu item "Control Options" to change
the control channel characteristics:
1 . Master Depend
2 . Crossfade
3 . Blackout function
4 . Full / flash function
– Menu item "Reset All Opt's" to reset all
changes made under "Output Options"
and "Control Options" to the presetting
2) Select the menu item with button NO or YES .
3) Select the parameters with button
4) Change the adjustment with button NO
or YES or numerical direct input with the
numerical keys .
5) Exit the menu by (repeated) pressing of button
ESC / SETUP .
button YES, without
CFT
, adjust the
+CFT
. Enter the

. Enter the new scene

): Select the step with
+CFT
, go to the

, ) .
 
or .
 
23