Short Overview Of The Operation - IMG STAGE LINE DMX-1440 Bedienungsanleitung

8

Short Overview of the Operation

Adjusting a scene
1) Select the control channel group(s) with buttons
CTRL CHANNEL PAGE [1..12] to [85..96].
2) Adjust the fader MASTER LEVEL to maximum
value.
3) Adjust the scene with the sliding controls (last
value must be "fetched" by the fader).
4) If necessary, activate the control lever MOTION
CONTROL for coarse presetting (with STICK
CONTROL ASSIGN 1/2 and/or 7/8: the LED be-
low the corresponding sliding controls lights up).
Crossfading to another adjustment
1) Adjust the 1st scene.
2) Press button HOLD: LED HOLD/CROSSFADE
lights up.
3) Adjust the 2nd scene.
4) Adjust the crossfading time with the control C.F.
TIME.
5) Press button HOLD: the crossfading starts – or
crossfade manually.
Manual crossfading
1) Turn the control C.F. TIME to the right stop: Dis-
play: "CFTIME: manu.", LED MANUAL CROSS-
FADE lights up.
2) Set crossfader MANUAL CROSSFADE to an end
position.
3) Move the crossfader to the other end position:
The crossfading starts running. When reaching
the other end position, the crossfading stops.
Memorizing a scene
1) Adjust the scene.
2) Select the bank with buttons
BANK and numerical keys [0] [1] ... [2] [0].
3) Press button STORE.
4) Press the button for the scene [1] ... [12].
Calling a scene
1) Select the bank with buttons
BANK and numerical keys [0] [1] ... [2] [0].
2) Adjust the crossfading time with control C.F.
TIME.
3) Press the scene button [1] ... [12]: crossfading
starts – or crossfade manually.
Flash buttons
Function "FLASH CHANNEL"
1) Press button FLASH MODE so many times until
the red LED FL. CH. lights up.
2) Select the control channel group(s) with buttons
CTRL CHANNEL PAGE.
3) Keep the flash button (below the sliding controls)
pressed.
Function "FLASH GROUP"
1) Press button FLASH MODE so many times until
the yellow LED FL. GRP. lights up.
2) Keep the flash button [1] ... [5] pressed.
Function "SHOW VALUE"
1) Press button FLASH MODE so many times until
the green LED SH. VAL. lights up.
2) Select the control channel group with button
CTRL CHANNEL PAGE.
3) Press the flash button: the display shows the cor-
responding channel value.
Programming a flash group
1) Keep button FLASH MODE pressed and press
button STORE: LEDs FL. CH. and FL. GRP. light
up.
2) Select the channels with buttons CTRL CHAN-
NEL PAGE and the flash buttons.
, or button
3) Press button STORE: LED FL. CH. is extin-
guished, LED FL. GRP. is still illuminated.
4) Press the flash button [1] ... [5] for the desired
group memory.
Changing a flash group
, or button
1) Press button FLASH MODE so many times until
the yellow LED FL. GRP. lights up.
2) Keep the corresponding flash button(s) [1] ... [5]
pressed and press button STORE: LEDs FL. CH.
and FL. GRP. light up.
3) Select additional channels or cancel selected
channels (with buttons CTRL CHANNEL PAGE
and the flash buttons).
4) Press button STORE: LED FL. CH. is extin-
guished, LED FL. GRP. is still illuminated.
5) Press the flash button [1] ... [5] for the desired
group memory.
Run of a scene sequence
1) Press button SEQUENCE: The green LED RUN
lights up.
2) Select the sequence number with the numerical
keys [0] [1] ... [6] [0].
Time-controlled start
1) Specify the speed with control SEQUENCER
SPEED or press button TAP SPEED twice.
2) If the selected sequence is not of type "+CFT"
(i. e. with memorized crossfading times), adjust
the crossfading time with control C.F. TIME.
3) To start, press button YES.
4) To change the direction, press button
ward) or (backward).
Music-controlled start
1) Press button AUDIO. Display: "Audio Trig." The
sequence starts by the audio signal of the jack
AUDIO IN or of the internal microphone.
2) Match the sensitivity with control AUDIO SENS.
3) If necessary, reduce the crossfading time with
control C.F. TIME.
4) To change the direction, press button
ward) or (forward).
GB
(for-
(back-