Attaching Or Changing Sequence Steps; Inserting Sequence Steps; Deleting Sequence Steps; Starting The Scene Sequence - IMG STAGE LINE DMX-1440 Bedienungsanleitung

button ESC / SETUP (21) and enter the num-
bers again .
4) The DMX values of the selected scene are
now sent to the output as a check . The ques-
tion is displayed . Confirm the scene
o.k.?
selection with the button STORE / PRG (22)
or the button 12 / YES or discard the selec-
tion with the button 11 / NO and then enter
another bank number and scene number .
5) Only if the question
CF Time/Step?
been confirmed with the button 12 / YES:
Adjust the crossfading time with the control
C .F . TIME (7) and confirm it with the button
STORE / PRG .
6) To select the subsequent scenes for the se-
quence, repeat the operating steps 3) to 5) .
7) After the last scene has been programmed,
a) go to the sequence running mode with
the button SEQUENCE (26) [chapter 7 .2],
the red LED PRG is extinguished, the green
LED RUN lights up
or go to the direct mode (chapter 5) by
pressing the button again, the LED RUN
is extinguished or
b) go back with the button ESC / SETUP (if
necessary, press several times) to:
− the data of the programmed sequence,
− the programming of another sequence,
− the direct mode .

7.1.3 Attaching or changing sequence steps

1) After pressing the buttons SEQUENCE (26)
and STORE / PRG (22), select the two-digit
number of the sequence to be completed or
changed with the numerical keys (2) [chap-
ter 7 .1 .1] . The display shows in the upper
line the sequence number and the number
of the sequence steps, e . g .
and below it
DEL/Edit:
2) For attaching a new step at the end of the se-
quence, select the next free step with the cur-
sor key (23), e . g .
 Seq03 St016__/__
If a sequence already contains the number
of steps which is possible as a maximum for
this sequence type (display
or ), no further step can
Seq xx St120
be attached .
To change a memorized sequence step,
select it with the cursor keys
display shows e . g .
Seq12 St119 02/12
i . e . sequence No . 12, selected step 119, con-
tains the scene 12 from bank 2 . The DMX
values for the scene of the respective step
selected are sent to the output .
If it is a sequence for which a crossfad-
ing time has been memorized for each step,
when running through the sequence steps
with the button , the programmed cross-

fading time is displayed between the individ-
ual scene indications before the unit switches
to the next step by pressing the button
again . For changing the crossfading time
only, continue with the operating step 5) .
3) Enter the two-digit bank number and the
two-digit scene number for the displayed
step number with the numerical keys (2) . In
case of incorrect inputs, go back one oper-
ating step with the button ESC / SETUP (21)
and enter the numbers again .
4) The DMX values of the selected scene are
now sent to the output as a check . The ques-
tion is displayed . Confirm the scene
o.k.?
selection with the button STORE / PRG (22)
or the button 12 / YES or discard the selec-
tion with the button 11 / NO and then enter
another scene .
5) Only if a sequence with individual crossfad-
ing times is concerned: Adjust the crossfad-
ing time with the control C .F . TIME (7) and
confirm it with the button STORE / PRG .
6) To enter another sequence step, repeat the
operating steps 3) to 5) . To change another
has
sequence step, repeat the operating steps
from 2) second paragraph to 5) .
7) Finally stop the sequence programming
mode either by pressing the button ESC/
SETUP several times or actuate the button
SEQUENCE to go to the sequence running
mode (chapter 7 .2) .

7.1.4 Inserting sequence steps

1) After pressing the buttons SEQUENCE (26)
and STORE / PRG (22), use the numerical
keys (2) to select the two-digit number of
the sequence to be completed .
2) Use the cursor keys
sequence step before which a new step is
to be inserted .
3) Press the key INSERT (25) . The display now
shows
If the sequence already contains the num-
ber of steps which is possible as a maximum
for this sequence type, no further step can
be inserted and the message
full! ƊESC
sequence or to exit the sequence program-
ming mode, press the button ESC / SETUP
(21) several times correspondingly .
4) To enter bank number, scene number, and,
if necessary, crossfading time for the new
Seq03 015St
step, perform the operating steps 3) to 5)
.
?
of chapter 7 .1 .2 .
5) To insert further sequence steps, repeat the
operating steps 2) to 4) .
.
6) To stop the sequence programming mode,
actuate the button ESC / SETUP several times
Seq xx St060
or press the button SEQUENCE to change to
the sequence running mode .

7.1.5 Deleting sequence steps

, . The
  1) After pressing the buttons SEQUENCE (26)
,
and STORE / PRG (22), use the numerical
keys (2) to select the two-digit number of
the sequence to be completed .
2) With the cursor keys
sequence step to be deleted .
3) Press the button DELETE (24) . The safety re-
quest
4) Confirm the deletion with the button 12 / YES
or cancel it with the button 11 / NO . After
deleting, the subsequent steps advance ac-
cordingly . If the deleted step was the only

step of the sequence, the display shows that
this sequence is blank again:
blank!
to programme a new sequence – see chapter
7 .1 .2 as from operating step 2) .
5) To delete further sequence steps, repeat the
operating steps 2) to 4) .
6) To stop the sequence programming mode,
actuate the button ESC / SETUP several times
or press the button SEQUENCE to change to
the sequence running mode .
, (23) to select the
 
.
Seq xx St xxx __/__
Seq xx is
is displayed . To select another
, (23) select the
 
is displayed .
Remove Step?
Seq xx is
. It is possible to start immediately

7.2 Starting the scene sequence

1) Press the button SEQUENCE (26) . Next to
the button, the green LED RUN lights up and
the display shows
Seq__
. However, the configuration menu
quence
must not be called [to exit it, press the but-
ton ESC / SETUP (21)] or the hold mode must
not be activated [to switch it off, press the
button HOLD (3)] .
2) Directly enter the two-digit sequence num-
ber with the numerical keys (2), e . g . for se-
quence 5 the buttons 0 and 5 (pay attention
to the lower lettering of the buttons) . The
display shows information on the selected
sequence:
for an unused (not
Seq xx is blank!
programmed) sequence number
or e . g .
Seq11 014St +CFT
quence No . 11 which consists of 14 steps
with individual crossfading time .
In case of incorrect inputs, go back one
operating step with the button ESC / SETUP
(21) and enter the number again .
3) For sequences for which the crossfading
times have been memorized (display
the control C .F . TIME (7) is without func-
tion when the sequences are running . For
sequences of the other type (
displayed), adjust the crossfading time be-
tween the steps of the sequence with the
control C .F . TIME (position MAN see chapter
7 .2 .1) . This can be made prior to the start
of a sequence, but also during the run of a
sequence .
4) The yellow rhythm LED above the but-
ton TAP SPEED (20) starts to flash to the
rhythm of the change of scene according to
the adjustment of the control SEQUENCER
SPEED (5) . To change the sequence running
speed, adjust this control to the desired
rhythm time or press the button TAP SPEED
twice for a more precise input: After the first
pressing, the yellow rhythm LED lights up,
after the second pressing, it is extinguished .
The time between the two actuations of
the button defines the time until the next
change of scene . If the button TAP SPEED
is pressed only once, after approx . 13 min-
utes of running, this maximum time is auto-
matically adjusted as the rhythm time . The
rhythm LED is extinguished .
Note: If the adjustment via the button TAP SPEED
does not seem to function, it may be due to the
fact that the crossfading time adjusted with the
control C .F . TIME is too long .
5) The second display line shows
. Define with one of the sub-
Y/N/AU/
sequent buttons if the sequence is to be
started and in which mode:
Button 11 / NO (2): cancel start
The sequence is not started; a new se-
quence number can be selected .
Button 12 / YES (2): time-controlled run
The sequence is started time-controlled
with the adjusted rhythm time . The
rhythm time may be changed while the
sequence is running .
If the yellow rhythm LED flashes while
crossfading, a new sequence step is not
yet made . The current crossfading is
stopped first and the unit crossfades to
the next scene at the subsequent flashing .
,
Select Se-
for the se-
),
+CFT
is not
+CFT
Start?
21