Heating The Appliance To Make The Dough Rise; Cleaning And Maintenance - BOMANN CB 593 Bedienungsanleitung

Baking Baking
Baking Baking
The bread baking machine sets the baking temperature and time automatically. If the bread is too light at the
end of the baling program, use the BACKEN program to let it brown more.
To do so, press the
degree of baking has been reached, stop the process.
Warming Warming Warming Warming
Once the baking is over, the buzzer goes off to signal that the bread or specialty can be removed. The 1-hour
warming time starts immediately.
End of the program phases End of the program phases End of the program phases End of the program phases
Please switch the appliance off at the end of the programme by setting the On/Off switch (L) to "0". Now
remove the baking tin using oven cloths, turn it over and as long as the bread does not immediately fall onto the
grid, move the kneading shaft back and forth a few times from below until the bread falls out. If one of the
kneading pegs is still stuck in the bread, take the hook supplied with the appliance. Insert it under the warm loaf
of bread into the almost circular opening of the kneading peg and wedge the hook against the lower edge of the
kneading peg preferably where the blade of the kneading peg is located. Then pull the kneading peg carefully
out with the hook.You can now easily cut the bread and remove completely the kneading pegs.

Heating the appliance to make the dough rise

Heating the appliance to make the dough rise Heating the appliance to make the dough rise Heating the appliance to make the dough rise
The heating is switched on only if the room temperature is lower than 25°C. If the room temperature is above
25°C the ingredients are already at the right temperature and there is no need for pre-heating. For the first and
second rising the room temperature must be above 25°C or high enough to make the dough rise without extra
heating.
Before using the appliance for the first time wash the bread baking machine's baking tin (never dip in water)
•
with water and clean the kneading pegs.
It is highly recommended to coat the new baking tin and the kneading pegs with heat resistant grease
•
before using them for the first time and let them heat in the oven for about 10 minutes at 160°C. Once
these have cooled down clean away (polish) the grease from the baking tin with a sheet of paper towel.
This operation is to be performed to protect the nonstick coating. This operation can be repeated from time
to time.
After use always leave the appliance to cool before cleaning it or putting it away. It takes about half an hour
•
for the appliance to cool and to be ready again for baking and kneading.
Before cleaning pull out the plug and leave the appliance to cool. Never use chemical cleaning agents,
•
gasoline, oven cleaners or any detergent that can scratch or ruin the coating.
Remove all the ingredients and crumbs from the lid, casing and baking compartment with a moist towel.
•
Never dip the appliance in water nor fill the baking compartment with water! The lid can be removed for Never dip the appliance in water nor fill the baking compartment with water! Never dip the appliance in water nor fill the baking compartment with water! Never dip the appliance in water nor fill the baking compartment with water!
easy cleaning. Remove the lid flap behind the lid hinge. You can then carefully remove the lid by pushing it
backwards. To replace it, act in the reverse order.
Wipe the outside of the baking tin with a moist towel. The inside of the tin can be washed with hot water.
•
Please do not immerse it in water for longer period and do not use any washing-up liquid.
Both the kneading pegs and drive shafts need to be cleaned immediately after use. If the kneading pegs
•
remain in the tin, it becomes difficult to remove them afterwards. In this case fill the container with warm
water and leave it to rest for 30 minutes. Then remove the kneading pegs.
The baking tin has a nonstick coating. Do not use metal objects that can scratch the surface when cleaning
•
it. It is normal that the color of the coating changes over the course of time. This change does not alter ist
effectiveness in any way whatsoever.
Before putting the appliance away for storage, make sure that it is perfectly cool, clean and dry. Put the
•
appliance away with the lid closed.
24
START/STOP key, then select the BACKEN program and start. When the desired

Cleaning and Maintenance

Cleaning and Maintenance Cleaning and Maintenance Cleaning and Maintenance