Maintenance And Cleaning - Scheppach 3906101704 Originalbetriebsanleitung

GB
When you release the trigger, you can read
the actual tyre pressure on the manometer.
Note: Increasing the tyre pressure by max. 0.2 bar,
will have a positive effect on the fuel consumption
of your car.
Deflation of Air
If the tyre pressure is too high, use the deflation button
(2b) and slowly reduce the air pressure to the desired
value.
• Compressed-air gun + suction-feed can
1. Before starting to work, check the trigger (3c) and
make sure it moves freely.
2. Connect the quick coupling connector (3d) of the
air spray gun to the compressed air supply. The
air should be regulated and filtered. Setup the air
pressure according to the parameters supplied with
the material to be processed and according to the
technical data.
3. Fill the container (3b) with the material to be pro­
cessed. Firmly screw on the container to the spray
gun. Alternatively connect the desired disposable
material can to the screwed connection of the spray
gun. Pay attention to the air hose while operating
the spray gun. Hold the hose with one hand while
you are operating the spray gun with the other hand.
The hose must not be bent. Do not step on it, as this
will lead to formation of droplets.
4. Press the trigger (3c) and perform test runs on
some test pieces. This way you can determine the
optimum spraying strength and the different jet
adjustments.
m Note
– Always keep down the material container when
spraying with the gun to prevent spraying material
from spilling and running out.
– Do not process abrasive, acid and petrol.
– Only use a solvent-resistant and pressure-resistant
air hoses (min. 10 bar).
• Compressed-air gun
– The blow-out gun is equipped with a quick coupling
connector (4c). Use the quick coupling connector to
connect the blow-out gun with the compressed air
supply.
– Activate the compressed air generator.
– Press the trigger (4b) to start the delivery of the air.
The farther the trigger is pressed, the stronger the
air jet will be.
– Release the trigger to stop the delivery of air.
– After work disconnect the tool from the compressed
air generator.
20/ 68
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002- 58
FR FR GB GB FR FR DE DE GB GB FR FR DE DE GB GB

9. Maintenance and cleaning

m CAUTION
Disconnect the device from the compressed air supply
before cleaning it.
• To ensure proper functionality and a long lifetime, dili­
gent lubrication and maintenance is essential.
• For operating pneumatic tools clean air is required.
Corrosion residues, dust and dirt from the pneumatic
pipes reduce the efficiency of the tool and will cause
technical problems.
• If necessary clean the units and the accessory with a
moist cloth.
• Do not use abrasive or aggressive chemicals as ben­
zene or thinner, which may dissolve plastic parts.
• Do not allow liquids to enter the tools and never im­
merse them into liquids. Water in the compressed air
inlet can damage the machine. Therefore it is recom­
mended to drain the air lines and the compressor in
regular intervals! Also clean the air filters in regular
intervals.
• Cleaning of the Paint spray gun with gravity-feed
can
Cleaning (by using of water soluble material)
When using water-soluble coating material, simply
clean all parts of the air paint spray gun thoroughly
with water.
Intensive Cleaning (by using of non water soluble
material)
• Please note that disassembling and intensive clean­
ing of the paint spray gun are inevitable, as other­
wise it can lead to debris and to a bad spray result,
if lacquer and priming coats are used as coating
material.
• Clean the paint spray gun and the paint container
after each use with appropriate paint thinners or
cleaning agents. Empty the contents. Fill a little
paint thinner into the paint container and rinse it.
Empty the paint container and repeat the process
again with clean paint thinner. Spray the clean paint
thinner in short strokes.
• During cleaning please always wear a mask and
solvent-resistant gloves! Also wear eye protection,
as splashes of solvents can cause injuries of your
eyes.
• Never put the paint spray gun into solvents for a
longer period of time or overnight.
• Never use hard or sharp objects to remove paint
residues. The nozzle must always be kept clean.
Debris of dried paint can distort the paint jet and
damage the spray gun.
• Rinse all parts well after intensive cleaning and dry
the paint spray gun. Assemble the gun. Fill a small
amount of paint thinner into the paint container and
blow it with compressed air through the spray gun.
FR FR DE DE GB GB FR FR DE DE GB GB FR FR