Technical Data; Before First Use - Scheppach 3906101704 Originalbetriebsanleitung

GB
Residual risks and accident prevention
standards
Neglect of ergonomic principles
Negligent handling of personal protective equip-
ment (PPE)
Negligent handling or ommission of the personal protec­
tive equipment may cause serious injuries.
– Wear prescribed personal protection equipment.
Human behaviour, misbehaviour
– For any work be fully concentrated.
m Residual risks - Cannot be entirely excluded.
Danger from noise
hearing damage
Prelonged unprotected work with the device may
cause hearing damage.
– Always wear ear-muffs.
In case of emergency
In case of a possibly occuring accident take the neces­
sary first aid steps as appropriate and obtain qualified
medical aid as quickly as possible.
If you obtain aid please give the following informa-
tions:
1. Where did it happen
2. What happend
3. How many injured
4. Type of injury
5. Who is reporting!

6. Technical data

Air Spray Gun
Operating Pressure bar
Max. Operating Pressure bar
Max. Air Consumption l/min
Paint Container Capacity l
Tyre Inflator
Operating Pressure bar
Max. Operating Pressure bar
Air Spray Gun
Operating Pressure bar
Max. Operating Pressure bar
Container Capacity l
Blow-out Gun
Operating Pressure bar
Max. Operating Pressure bar
Air Spiral Hose
Operating Pressure bar
Max. Operating Pressure bar
Length m
18/ 68
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002- 58
FR FR GB GB FR FR DE DE
0­8
8
180
0,6
3­8
8
0­8
8
0,9
3­8
8
0­8
8
5
GB GB FR FR DE DE GB GB

7. Before first use

Connect:
Push the nipple on your compressed air hose into the
quick-release coupling, the sleeve will automatically
spring forwards.
Disconnect:
Pull back the sleeve and remove the hose.
m WARNING
As you release the hose coupling, hold the hose cou­
pling part in your hand to prevent injuries caused by the
hose being thrown backwards.
The compressed air hose is also fitted with a quicklock
coupling to which accessories can be connected as de­
scribed above.
• Useing of the Compressed-air hose
– Use the air spiral hose to connect the compressed
air tool with the compressed air supply.
– Connect the quick coupling connector (5b) with the
air supply and connect the air tool connection (5a)
with the compressed air tool.
• Useing of the Paint spray gun with gravity-feed
can
­ Preparing the Surface to be painted
The object to be painted, or the surface, etc. has
to be clean, dry and free of grease and dust. Metal
surfaces must be stainless. Since the fine sprayed
paint is dispersed in a very thin layer on the surface,
roughness would have a negative effect on the paint
result.
­ Viscosity testing
Viscosity is the flow rate of a material. Measure the
viscosity with a viscosity cup (not included) as fol­
lows:
1. Thin the paint according to the manufacturer's
recommendation. Start with less thinner so
you still can and add some thinner later.
2. Mix the paint thoroughly. Pour the
paint into the viscosity cup or dip the
cup to the edge into the paint.
3. Measure the time in seconds until the liquid
thread breaks off. This flow time is called DIN-s.
Thin the material as much as necessary until the
liquid thread already breaks off after 20 seconds.
­ Paint Jet Adjustment
– For a wide jet (horizontally), align
the nozzle (1a) vertically.
– For a high jet (vertically), align the nozzle (1a)
horizontally. Use this setting for spraying larger
areas.
– Use flat-nose pliers to adjust the nozzle if neces­
sary.
FR FR DE DE GB GB FR FR DE DE GB GB FR FR