Kärcher MIC 45 classic Originalbetriebsanleitung Seite 27

Installing and connecting the battery
 Insert battery in battery mount.
 Connect pole terminal (red cable) to
positive pole (+).
 Connect pole terminal to negative pole
(-).
 Screw the battery and its holder to the
floor.
Note
Before removing the battery, make sure
that the negative pole lead is disconnected.
Check that the battery pole and pole termi-
nals are adequately protected with pole
grease.
Charging battery
Danger
Risk of injury! Comply with safety regula-
tions on the handling of batteries. Observe
the directions provided by the manufacturer
of the charger.
Danger
Charge the battery only with an appropriate
charger.
 Unscrew all cell caps.
 Connect positive terminal cable from
the charger to the positive pole connec-
tion on the battery.
 Connect negative terminal cable from
the charger to the negative pole con-
nection on the battery.
 Plug in mains connector and switch on
charger.
 Charge battery using lowest possible
level of charging current.
Note: When the battery is charged, first re-
move the charger from the mains and then
disconnect it from the battery.
Replacing wheel
Danger
When carrying out repairs on public high-
ways, wear warning clothing when working
close to passing traffic.
Danger
Risk of injury!
 Park the machine on an even surface.
 Activate parking brake.
 Remove ignition key.
 Check stability of ground. Also secure
the machine with wheel chock(s) to pre-
vent it rolling away.
 Position vehicle jack at the appropriate
mounting point for the front or rear
wheel.
Note
Use a suitable commercially available vehi-
cle jack.
 Loosen the wheel nuts/wheel bolts by
about 1 revolution using a suitable tool.
 Raise machine using vehicle jack.
 Unscrew the wheel nuts/wheel bolts
and remove them.
 Remove wheel.
 Have the defective wheel repaired by a
specialised repair shop.
 Place the wheel and screw in the wheel
nuts/wheel bolts all the way; tighten
them lightly.
 Lower machine using vehicle jack.
 Torque the wheel nuts/wheel bolts to
the required torque.
MIC 45 advanced
MIC 45 classic
Remove/attach engine panels
To complete the different maintenance
tasks, the side panels must be removed.
Grasp the top panel by the rear end and
pivot it up against the resistance.
Warning
Risk of burns Let the appliance cool off be-
fore removing the panels.
Remove the engine's side panels
1 Right side panel lock
2 Left side panel lock
 Open both locks.
 Lift the panel up toward the top and re-
move it to the side.
Install the engine's side panels
 Insert the panels from the side.
 Hook the panel into the mounting
groove on the upper edge.
 Slide the panel into the desired position
and secure with the locks.
10
-
EN
Check engine oil level and top up, if re-
quired
1 Oil dipstick
2 Oil fill cover (motor)
180 Nm
 Pull out oil dipstick.
300 Nm
 Wipe off oil dipstick and insert.
 Pull out oil dipstick.
 Read the value of the oil level.
 Insert the oil dip again.
The oil level must lie between "MIN"
–
and "MAX" marking.
Add motor oil if the oil level is below the
–
"MIN" marking.
Do not fill oil above the "MAX" marking.
–
 Unscrew the oil fill lid.
 Fill in motor oil.
For oil type refer to Chapter "Technical
specifications".
 Close the oil fill lid.
 Wait at least 5 minutes.
 Check engine oil level.
Caution
An oil level that is too high leads to damag-
es of the engine by overheating. If the oil
level exceeds the "MAX" mark, oil must be
drained until the correct oil fill level has
been reached.
Change the motor oil and the oil filter
 Every 100 operating hours: Replace the
engine oil.
 Every 200 operating hours: Change the
motor oil filter.
Note: A warm motor facilitates the draining
process.
Danger
Risk of burns due to hot oil or possible hot
hose lines!
 Ready a catch bin for appr. 6 litre oil.
 Unscrew oil drain plug.
 Unscrew the oil fill lid.
 Drain off oil.
 Unscrew the oil filter.
 Clean the intake and sealing areas.
27