Scheppach MIX125 Originalbetriebsanleitung Seite 31

3. Now place the mixing unit (2) on the mounted
cross-head screws and fix it with one washer, one
spring washer and one M8 nut each.
4. The mixing unit (2) is not tightened until the upper
part of the drum (9) has been mounted.
Note: In order to make correct installation of the mixing
unit (2) easier, two arrows are attached to the upper
and lower drum. If you are not sure whether the mix-
ing unit has been installed correctly, you can test this.
To do this, place the upper part of the drum (9) on the
lower part of the drum (10) and turn them until the two
arrows point towards each other.
Fitting drum upper section (9) (enclosed accesso-
ries bag F) (Fig. 9)
1. Put the upper part of the drum (9) on the lower part
of the drum (10). Make sure that the fixing holes of
the upper and lower drum align with each other.
Attention! The glued-on arrows mark the exact
alignment of the drum lower section (10) and drum
upper section (9).
2. Fix the upper part of the drum (9) by inserting the
six M8x16 screws, the spring washers and wash-
ers.
3. Then tighten the screws crosswise using a Phillips
screwdriver (not included in the scope of delivery).
4. Insert one M8x20 Phillips screw each through the
upper part of the drum (9) from the outside.
5. Push one rubber washer each onto the Phil-
lips-head screws just inserted in the upper part of
the drum (9).
6. Attach the upper end of the mixing unit (2) by plac-
ing it on the Phillips screws just inserted. Fix it with
one washer, one spring washer and one nut M8
on each.
7. Finally, tighten all four screws in the lower drum
section (10) and upper drum section (9) using a
Phillips screwdriver and a size 13 open-end span-
ner (not included in the scope of delivery).
Installing the locking disc (13) (enclosed accesso-
ries bag G) (Fig. 10)
1. Push the locking disc (13) onto the holder (13a).
2. Fix them with the two hexagonal screws M8x25
and one washer, one spring washer and one nut
M8 each.
3. Then tighten all screws using one or two open-end-
ed spanners (size 13) (not included in the scope of
delivery).
Installing the swivel wheel (7) (enclosed accesso-
ries bag H) (Fig. 11)
1. Insert the washer and then the spring from below
into the tube of the swivel wheel (7).
2. Hold the spring in place with a finger.
3. Place the swivel wheel (7) above the shaft of the
drum lower section (10) so that the spring lies on
the shaft.
4. Push the swivel wheel (7) down until the holes in
the shaft of the drum lower section (10) align with
the holes in the swivel wheel (7).
5. Fix the swivel wheel (7) with the M10x65 hexagon
head screw, two washers and a stop nut.
6. Then tighten the screw using two open-ended
spanners size 16 (not included in the scope of de-
livery) until the swivel wheel (7) can still be tilted
easily.
7. Turn the cylinder screw of the tube clockwise using
an 8 mm Allen key (not included in the scope of de-
livery) to adjust the spring tension.
Note: The swivel wheel (7) must be able to tilt when
mounted on the shaft. It must be able to grip easily into
the recesses of the locking disc (13).
Installing the motor unit (4) (enclosed accessories
bag I) (Fig. 12)
1. Position the motor unit (4) such that the threaded
bolts match the holes.
2. Now push the motor unit (4) completely onto the
shaft.
3. Then fix the motor unit (4) with the four washers
and the four M8 stop nuts. Use an open-ended
spanner (size 13) for this (not included in the scope
of delivery).
9. Start-up
Attention!
Always make sure the device is fully assembled before
commissioning!
Only operate the concrete mixer if no parts are missing
or faulty and if the connection cable is not damaged.
9.1 Setting up
1. Set up the concrete mixer horizontally on a level,
non-tilting and firm surface. Prevent the machine
from sinking into the ground.
2. Do not set up the concrete mixer on the connection
cable!
www.scheppach.com GB | 31