Start-Up; Technical Data - Scheppach PM1400 Original Bedienungsanleitung

7. Start-up

Turning on and off
Turning on (fig. 1)
Press and hold the circuit breaker (8) for the ON /
OFF switch; now you can press the ON / OFF switch
(7) to start the handheld mixer. Once the tool is run-
ning properly you can release the ON / OFF switch,
turning off the circuit breaker (8).
Turning off (fig. 1)
Release the ON / OFF switch (7). The circuit breaker
for the ON / OFF switch (8) turns off automatically.
Speed controller (fig. 1)
With the speed controller (9), the power tool's speed
can be gradually adjusted. The type of material to be
mixed determines the speed rate that is required.
Practice will teach you the optimal speed required
by the respective material.
2- speed gear (fig. 1)
The device is equipped with a 2-speed gear. If the
gear selection switch cannot be locked, turn the stir-
ring staff a little.
• For the speed selection turn the switch (4) by 180°.
1. speed: 0 min - 570 min
–1
2. speed: 0 min - 760 min
-1
Only operate this switch at standstill of the ma-
chine.
Working with the paint and mortar mixing tool
Before changing the mixing tool you must pull the
power plug.
Reduce the working speed when you immerse the
mixing tool into the material you want to mix and
when you take it out again. When the mixing tool is
fully immersed, raise the speed to maximum in order
to ensure adequate cooling of the motor. Move the
mixing tool through the mixing container during the
mixing operation. Continue mixing until all the mate-
rial has been thoroughly processed. When you are
finished with your mixing work, clean the mixing tool.
Area of application of the agitators (fig. 1)
• The left-turning agitator (2a) is used for low-viscos-
ity substances such as: Different types of paints,
varnishes, glazes, wallpaper paste, sealing com-
pounds, bitumen, chemicals, red lead, cement
slurries
• The right-turning agitator (2b) is used for high-vis-
cosity substances such as: Adhesive and ready­
mixed mortars, adhesive binders, gypsum, lime,
cement plaster, screed, concrete, tile adhesive,
glue, putty, pastes, granulate
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
–1
-1

8. Technical data

Mains voltage
Power input
Idling speed 0-570 min
Mixing tool mount
Protection class
Weight
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 60745.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Vibration emission value ah = 5.673 m/s
K uncertainty = 1.5 m/s
2
Additional information for electric power tools
Warning!
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to com-
pare the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
230 V~, 50 Hz
1400 W
/ 0-760 min
-1 -1
M14
II
4.9 kg
89 dB(A)
3 dB(A)
100 dB(A)
3 dB(A)
2
GB | 19