Bosch GKF 18V-8 Professional Originalbetriebsanleitung Seite 21

www.elektromarkabolt.hu
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for copy routing as well as routing
grooves, edges, profiles and elongated holes in wood,
plastic and light building materials while resting firmly on the
workpiece.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Motor unit
(2) Fixed routing base
(3) Speed preselection thumbwheel
(4) Thumbwheel for fine adjustment of routing depth
(5) Router bit
(6) Cap nut with collet
(7) Base plate
(8) Spindle locking lever
(9) Scale for setting the routing depth
(10) Clamping lever
(11) On/off switch
(12) Rechargeable battery
(13) Rechargeable battery release button
(14) Handle (insulated gripping surface)
(15) Collet
(16) Shaft
(17) Open-ended spanner (17 mm)
(18) Knurled screw for attachments (19), (21), (32),
(33)
(19) Parallel guide
(20) Wing bolt for parallel guide
(21) Flush trim roller guide
(22) Wing bolt for fixing the horizontal alignment
(23) Wing bolt for the horizontal alignment of the flush
trim roller guide
(24) Guide roller
(25) Tilt base
(26) Wing bolt for angle adjustment
(27) Scale for routing angle adjustment
(28) Plunge base
(29) Offset base
(30) Chip shield for edge routing
(31) Nut for adjustment of the tensioning force
(32) Dust extraction adapter for routing edges
(33) Dust extraction adapter for routing grooves
(34) Deluxe routing guide
(35) Clamping lever (plunge base)
Bosch Power Tools
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
(36) Release lever for plunge action (plunge base)
(37) Dust extraction for routing grooves (plunge base)
(38) Dust extraction for routing edges (plunge base)
(39) Drive wheel (for offset base)
(40) Opening in the base plate (offset base)
(41) Spindle lock button (offset base)
(42) Roller/bush guide (offset base)
(43) Guide bushing
(44) Adapter for guide bushing
(45) Centring pin
(46) Centring cone
(47) Rib in fixed routing base
(48) Depth adjustment channel on the motor unit
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Edge router
Article number
Rated voltage
No-load speed A)
Speed preselection
Constant electronic control
Compatible collets
Fixed routing base stroke
Weight B)
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation
during storage
Recommended rechargeable
a)
batteries
Recommended chargers
A) Measured at 20–25 °C with rechargeable battery ProCORE18V
5.5Ah
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
Values can vary depending on the product, scope of application and
environmental conditions. To find out more, visit
www.bosch-professional.com/wac.
Noise/Vibration Information
Noise emission values determined according
a)
to EN 62841‑2‑17.
English | 21
a)
a)
a)
a)
a)
a)
a)
a)
a)
GKF 18V-8
3 601 FC2 0..
V
min –1 10,000–30,000
mm
inches
mm
kg
°C 0 to +35
°C –20 to +50
C) and
GBA 18V...
> 4.0 Ah
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
1 609 92A 8BL | (12.03.2024)
a)
a)
18
●
●
6/8
¼"
34
1.094