Scheppach ke 70m Originalbetriebsanleitung Seite 19

• Keep the workplace free of wood debris and parts
lying around.
• Disorder in the work area can lead to accidents.
• Do not allow other persons, especially children, to
touch the product. Keep such persons away from
the workplace.
• Personnel working on the machine must not be
distracted.
• Observe the direction of rotation of the engine and
saw blade. Only use saw blades whose maximum
permissible speed is not less than the maximum
spindle speed of the circular saw and the material
to be cut.
• Under no circumstances should the saw blades be
braked by pushing against the side after switching
off the drive.
• Only install saw blades that are well sharpened,
free of cracks and not deformed.
• Do not use circular saw blades made of high-speed
alloy steel (HSS steel)
• Only use saw blades recommended by the manu-
facturer and which comply with EN 847-1.
• Faulty saw blades must be replaced immediately.
• Do not use saw blades that do not correspond to
the characteristics specified in these usage instruc-
tions.
• Safety equipment on the machine must not be dis-
assembled or made unusable.
• Replace worn table or swivel frame insert.
• Working position always to the side of the saw
blade.
• Do not load the machine so much that it comes to
a standstill.
• Make sure that cut-off pieces of wood are not caught
by the sprocket of the saw blade and flung away.
• Never remove loose fragments, chips or jammed
wood pieces from the running saw blade.
• To rectify faults or remove jammed pieces of wood,
switch the machine off. Pull out the mains plug.
• If the sawing gap has increased due to wear, re-
place the swivel frame or table inlay. Switch off the
machine and pull out the mains plug.
• Only carry out modifications, adjustments, meas-
urements and cleaning work when the engine is
switched off. Pull out the mains plug.
• Before switching on, make sure that keys and ad-
justing tools are removed.
• Switch off the engine and pull out the mains plug
when leaving the work station.
• All protective and safety equipment must be reas-
sembled immediately after repair or when mainte-
nance is completed.
• The safety, operating and maintenance informa-
tion of the manufacturer, as well as the dimensions
specified in the technical data, must be observed.
• The relevant accident prevention regulations and
the other generally accepted safety rules must be
observed.
• Do not use low-output machines for heavy work.
• Make sure that you have secure footing and always
maintain your balance.
• Check the product for potential damage!
• All components and protective devices must be
carefully inspected to ensure that they are fault-free
and function as intended prior to continued use of
the machine.
• Check whether the moving parts function faultless-
ly and do not jam or whether parts are damaged. All
parts must be correctly mounted and all conditions
must be fulfilled to ensure fault-free operation of
the product.
• Damaged protective devices and parts must be
repaired properly or replaced by a recognised spe-
cialist workshop unless otherwise specified in the
usage instructions.
• This product conforms to the applicable safety
regulations. Repairs may only be performed by
a specialist using original spare parts. Otherwise
accidents could occur.
• Wear suitable personal protective equipment. This
includes:
- Wear hearing protection to prevent the risk of
developing hearing loss,;
- Respiratory protection to avoid the risk of inhal-
ing damaging dust.
- Eye protection to prevent foreign bodies entering
the eyes.
- Safety shoes for stability and protection against
falling objects.
- Wear gloves when handling saw blades and
rough materials. Saw blades must be carried in
a container whenever practical.
- Safety goggles / face protection to avoid injuries
due flying objects.
- Protective clothing to prevent cutting injuries.
• The operator must be informed about the condi-
tions that affect the noise levels (e.g. saw blades
designed to reduce noise, care of saw blade and
machine).
• Faults in the machine, including the guards and the
saw blade, must be reported to the person respon-
sible for safety as soon as they are discovered.
• When transporting the machine, use only the trans-
port devices and never use the guards for handling
and transport.
• All operators must be adequately trained in the use,
setting and operation of the machine.
• Do not saw any material to be cut that contain for-
eign bodies such as wires, cables or cords.
• Arrange the workpiece stack to be processed and
the finished workpieces close to the normal work-
place of the operator.
• Only use original, undamaged flanges as specified
by the manufacturer and those that are suitable for
the purpose.
www.scheppach.com
GB | 19