GRAPHITE 58GE138 Benutzerhandbuch Seite 10

• Never cut several pieces of material at the same time.
• When operating the chainsaw, adopt a standing position to ensure
balance.
• All saw components must be properly fixed.
• Repairs to the chainsaw should only be carried out by a qualified
person at an authorised service workshop, using original spare parts.
• Profile cutting must not be carried out with the saw.
• When handling the saw, only grasp the transport handles, do not
grasp the saw component covers.
PROPER BATTERY HANDLING AND OPERATION
• The battery charging process should be under the control of the user.
• Avoid charging the battery at temperatures below 0°C.
• Only charge the batteries with the charger recommended by the
manufacturer. The use of a charger designed to charge a different type
of battery poses a risk of fire.
• When the battery is not in use, keep it away from metal objects such as
paper clips, coins, keys nails, screws, or other small metal items that
can short-circuit the battery terminals. Short-circuiting the battery
terminals can cause burns or fire.
• In the event of damage and/or misuse of the battery, gases may be
released. Ventilate the room, consult a doctor in case of discomfort. The
gases may damage the respiratory tract.
• Fluid leakage from the battery can occur in extreme conditions. Liquid
leaking from the battery can cause irritation or burns. If a leak is
detected, proceed as follows:
• Carefully wipe off the liquid with a piece of cloth. Avoid contact of the
liquid with the skin or eyes.
• if the liquid comes into contact with the skin, the relevant area on the
body should be washed immediately with copious amounts of clean
water, or neutralise the liquid with a mild acid such as lemon juice or
vinegar.
• if the liquid gets into the eyes, rinse them immediately with plenty of
clean water for at least 10 minutes and seek medical advice.
• Do not use a battery that is damaged or modified. Damaged or modified
batteries may act unpredictably, leading to fire, explosion or danger of
injury.
• The battery must not be exposed to moisture or water.
• Always keep the battery away from a heat source. Do not leave it in a
high temperature environment for long periods of time (in direct
sunlight, near radiators or anywhere where the temperature exceeds
50°C).
• Do not expose the battery to fire or excessive temperatures. Exposure
to fire or temperatures above 130°C may cause an explosion.
NOTE: A temperature of 130°C can be specified as 265°F.
• All charging instructions must be followed, and the battery must not be
charged at a temperature outside the range specified in the rating data
table in the operating instructions. Charging incorrectly or at
temperatures outside the specified range can damage the battery and
increase the risk of fire.
BATTERY REPAIR:
• Damaged batteries must not be repaired. Repairs to the battery are only
permitted by the manufacturer or an authorised service centre.
• The used battery should be taken to a disposal centre for this type of
hazardous waste.
SAFETY INSTRUCTIONS FOR THE CHARGER
• The charger must not be exposed to moisture or water. The ingress of
water into the charger increases the risk of shock. The charger may
only be used indoors in dry rooms.
• Unplug the charger from the mains before carrying out any
maintenance or cleaning.
• Do not use the charger placed on a flammable surface (e.g. paper,
textiles) or in the vicinity of flammable substances. Due to the
temperature increase of the charger during the charging process, there
is a danger of fire.
• Check the condition of the charger, cable and plug each time before
use. If damage is found - do not use the charger. Do not attempt to
disassemble the charger. Refer all repairs to an authorised service
workshop. Improper installation of the charger may result in a risk of
electric shock or fire.
• Children and physically, emotionally or mentally challenged persons, as
well as other persons whose experience or knowledge is insufficient to
operate the charger with all safety precautions, should not operate the
charger without the supervision of a responsible person. Otherwise
there is a danger that the device will be mishandled resulting in injury.
• When the charger is not in use, it should be disconnected from the
mains.
• All charging instructions must be followed, and the battery must not be
charged at a temperature outside the range specified in the rating table
in the operating instructions. Charging incorrectly or at temperatures
outside the specified range can damage the battery and increase the
risk of fire.
CHARGER REPAIR
• Do not repair a defective charger yourself. Repair of the charger is only
permitted by the manufacturer or an authorised service centre.
• The used charger should be taken to a disposal centre for this type of
waste.
ATTENTION: The device is designed for indoor operation.
• Despite the use of an inherently safe design, the use of safety
measures and additional protective measures, there is always a
residual risk of injury during work.
• Li-Ion batteries can leak, catch fire or explode if they are heated to high
temperatures or short-circuited. Do not store them in the car during hot
and sunny days. Do not open the battery pack. Li-Ion batteries contain
electronic safety devices which, if damaged, can cause the battery to
catch fire or explode.
PURPOSE
The tile cutting machine is intended for wet cutting of ceramic tiles or
similar materials suitable for the size of the saw itself. It is not permitted to
use the cutter for cutting wood or metal. Only cutting discs intended for this
type of machine must be used with the cut-off saw. Segmented discs
must not be used for cutting. The cut-off saw has been designed for all
work within the scope of independent amateur activity (DIY). The saw is
driven by a DC brush motor, battery-powered.
Do not misuse the device.
PICTOGRAMS AND WARNINGS
Read the operating instructions, observe the warnings and safety
conditions contained therein!
The product complies with the regulations of the European Union
Use personal protective equipment: eye, hearing and respiratory
protection
Wear protective gloves
Segmented discs must not be used with the machine
Risk of hand injury
Remove the battery from the unit before repair and maintenance
Keep away from children
Recyclable
Do not dispose of with household waste.
DESCRIPTION OF THE GRAPHIC ELEMENTS
The numbering below refers to the components of the device
shown on the graphic pages of this manual.
Designation
1 Angle guide lock knob
2 Parallel guide
3 Angle guide
45° edge guide
4
5 Parallel guide locking clamps
6 On/off switch
7 Guide ruler
8 Diamond disc protector
9 Guide ruler
Edge guide lock 45°
10
10
Description